Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Analog Line Level Preamplifiers , Passive Pre-amps, Crossovers, etc.

(crudely) approximating a loudness circuit
(crudely) approximating a loudness circuit
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 28th December 2018, 01:10 PM   #1
uraberg is offline uraberg  United States
diyAudio Member
 
Join Date: Apr 2017
Default (crudely) approximating a loudness circuit

I'm probably way off base here, but I got this harebrained idea.

Imagine a 4 way dsp'ed active bluetooth speaker, driven by two stereo amps modules (one for bass, one for mid/high), both with volume control, and some measure of variable gain (TDA7498E in my case). The volume on these modules gets set at a certain value, and then left alone, with main volume control being your bluetooth device.

What if we set the gain on the amp that drives the bass, at a lower level than the amp that drives the mid and high, but the volume on the bass amp higher.

Would the net effect be that the bass attenuates less than the mid/highs, if we use the bluetooth device to reduce the volume of the system? This of course assumes that amplification is steeper with a higher gain, which i don't know is true...

Idle minds are wondering about this stuff...

Last edited by uraberg; 28th December 2018 at 01:25 PM.
  Reply With Quote
Old 31st December 2018, 12:17 AM   #2
MAAC0 is offline MAAC0  Portugal
diyAudio Member
 
Join Date: May 2010
?????
  Reply With Quote
Old 31st December 2018, 01:32 AM   #3
nigelwright7557 is online now nigelwright7557  United Kingdom
diyAudio Member
 
nigelwright7557's Avatar
 
Join Date: Apr 2008
Location: Carlisle, England
A loudness circuit usually boosts bass and treble at low volumes.
This is because the response of the ear drops off at low volumes at the top and bottom end.
__________________
PCBCAD51 download or CDROM 2019 version out now http://www.murtonpikesystems.co.uk
  Reply With Quote
Old 31st December 2018, 11:24 AM   #4
TMM is offline TMM  Australia
diyAudio Member
 
Join Date: Sep 2007
Location: Australia
Send a message via AIM to TMM
I assume by gain you are referring to the feedback resistors at the TDA7498E chip and by volume you are referring to some kind of input signal attenuator before the amplifier.

Since both gain and volume controls are linear (they don't impart non-linear distortion), decreasing one and increasing the other proportionally will result in no net effect*. If you were hoping that adjusting them in some way would result in a more bassy tonal balance when the system volume control is set low or high this is not the case. To achieve that would require some kind of non-linear or dynamic compression circuit applied to the bass signal. Usually this would be accomplished in DSP to achieve an effect that is volume dependant. Alternatively you can add a static EQ filter which can be manually enabled or disabled by a 'loudness' button like classic amplifiers/receivers typically have.

*Typically you want to run the gain of your amplifier as low as possible and the 'volume' or signal level as high as possible while still achieving an acceptable in-room sound level with the volume control at max. This ensures the best signal to distortion/noise ratio.

Last edited by TMM; 31st December 2018 at 11:30 AM.
  Reply With Quote

Reply


(crudely) approximating a loudness circuitHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Modifications to Loudness Circuit euromut Tubes / Valves 7 11th January 2018 01:26 AM
How preserve loudness circuit with new volume pot? mfaughn Tubes / Valves 8 17th February 2017 01:38 AM
Eico HF-32 PEC Loudness Circuit joeztech Tubes / Valves 11 31st March 2015 11:35 AM
PCB for this Loudness circuit - Help! formula 22 Solid State 1 26th October 2011 08:27 AM
Anybody have a formal loudness circuit? thaumaturge Solid State 10 12th September 2011 10:41 AM


New To Site? Need Help?

All times are GMT. The time now is 04:40 AM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.00%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright ©1999-2019 diyAudio
Wiki