|
Home | Forums | Rules | Articles | diyAudio Store | Blogs | Gallery | Wiki | Register | Donations | FAQ | Calendar | Search | Today's Posts | Mark Forums Read | Search |
Analog Line Level Preamplifiers , Passive Pre-amps, Crossovers, etc. |
|
Please consider donating to help us continue to serve you.
Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving |
![]() |
|
Thread Tools | Search this Thread |
![]() |
#2471 | |
diyAudio Member
|
Quote:
Yes, it is. I made Front panel in the same exactly way as I did it for my first unit and I used CNC. All the rest of drilling I did manually in my garage.IMG_1499.JPG |
|
![]() |
![]() |
#2472 |
diyAudio Chief Moderator
|
Yes, good plan. But only a few minutes will do. Just measure that their output voltage has fallen waaaay down before declaring the units empty of charge.
|
![]() |
![]() |
#2473 | |
diyAudio Chief Moderator
|
Quote:
|
|
![]() |
![]() |
#2474 |
diyAudio Member
Join Date: Dec 2014
|
I do have a 4-way XLR connected HD650 headphone.
But I will use the DCG3 as a single ended connected Preamp. What is the best way todo so? |
![]() |
![]() |
#2475 |
diyAudio Chief Moderator
|
The HD650 uses removable cable with Y split and connection points at the bases of its cups so remove the bridged drive connecting four pin XLR terminated cable from it and use the original cable with the jack connector that came in the manufacturer's box. If you want to keep the special cable for some reason like custom length or its mechanical quality you have to remove the XLR and rewire to a jack. Tip is left channel, ring is right channel, sleeve is the grounds.
|
![]() |
![]() |
#2476 |
diyAudio Member
Join Date: Oct 2016
|
Is there a reason not to use
a) a conversion cable (from 4-pin xlr to standard stereo jack), or b) mount a 4-pin female socket in the DCG3 chassis but wire it SE (so pins 1 and 3 to the SE outputs L+R and pins 2 and 4 to signal ground)? Steef |
![]() |
![]() |
#2477 |
diyAudio Chief Moderator
|
No electrical reason not to do conversion things or extra socket than to have a straightforward cable and a less busy featured front panel.
|
![]() |
![]() |
#2478 |
diyAudio Member
Join Date: Oct 2016
|
Thanks,
I myself was planning to use *only* a 4-pin XLR on my chassis and wire it SE Now I am pondering how on earth to back-mount a 4-pin Neutrik female panel connector to a 10mm thick front panel (considering these things have lock-tabs)... Steef |
![]() |
![]() |
#2479 | |
diyAudio Member
Join Date: Dec 2014
|
Quote:
... and using NC4FD-L-B-1front mount connectors ;-) |
|
![]() |
![]() |
#2480 |
diyAudio Member
Join Date: Oct 2016
|
... or remove the lock-tab (has anyone tested this)?
|
![]() |
![]() |
Thread Tools | Search this Thread |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
FS: Pass VFET 2 essential+supplemental kit and Salas DCG3 kit | 32y0 | Swap Meet | 3 | 16th April 2018 06:22 AM |
FS : Salas DCG3 | pinnocchio | Swap Meet | 2 | 9th January 2018 11:32 PM |
FS: 2x Salas DCG3 and DCSTB complete kits | bvtrinh | Swap Meet | 5 | 27th October 2017 12:29 AM |
WTB Salas DCG3 pcb or kit | savvas | Swap Meet | 0 | 8th February 2017 11:50 AM |
Using a line preamp to drive headphone | ginetto61 | Solid State | 25 | 6th May 2015 07:19 PM |
New To Site? | Need Help? |