Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

Amplifiers:Pass Labs Amplifiers

The Project

Introduction

Read this first

Goals

What were some of your goals with the design of the amp? In the end, did you achieve them? If not, where did the design fall short of your expectations?

examples: I wanted to create a class A amp that produced THD 0.00001% at 1KHz but I only achieved 0.01%

Specifications

NameDescription
Volatge Gain15.3 dB
BandwidthValue
PhaseValue
Sensitivity8 Ohm: Value, 4 Ohm: Value
S/N Ratio
~60 uV unweighted, 20-20 KHz
Rated Consumption180W
Idle Consumption180W
Harmonic DistortionDistortion @ 1 watt .001% to .005% @ 1 KHz
Harmonic SpectrumFFT plot/plots
Square/Step responseOscilloscope Trace
StabilityPhase margin + scope traces into capacitive loads
Output configurationsCan it be bridged? Parallel drive?
Output ImpedanceValue or plot/plots

Schematic/Blueprint

Please attach schematics to this wiki page. You can then use the tag to display them inline. Please don't be afraid to attach Gerber files to the page as well.

Note: There is a bug in the wiki right now where you can't add attachments to a wiki after 30 minutes.

Bill of Materials

PCB Availibility
http://www.diyaudio.com/store/pcb-ba...cb-set-45.html

Also Group Buys listed further down on this page.

Power Transformers




Either list them in this section or attach a file to the page that people can download.

Note: If this project uses other projects as components (maybe this is a full build and uses an amplifier and PSU from other projects, please list them here).

Simulations and Analysis

Embed the images for your simulations here along with descriptions for each of them so people know what you're talking about.

Construction (Steps / Tips / Notes)

This section is incomplete and will be a bit messy unyil I get all information into it.


GB F5 Guide (pcb version 2)
http://www.diyaudio.com/forums/blogs...version-2.html



F5 components, parts you use
http://www.diyaudio.com/forums/pass-...s-you-use.html

Project Initial Setup

Suggested start up should have the PS disconnected from the amp boards.
Also use a variac or dim bulb tester or both.

Variac
http://en.wikipedia.org/wiki/Autotransformer

dim bulb testers
http://www.diyaudio.com/forums/power...lb-tester.html




Bias Setting(thanks to ZM)

dial both pots to 0 ohms ( check with ohmmeter )

place one voltmeter across PSU caps ( best between + and - of PSU) to observe max voltage of PSU

place one voltmeter at output - to observe offset

place one voltmeter across one source resistors(R11 or R12) of output mosfets ; it doesn't matter which one .

for test - slowly dial up Variac ( presuming that you have one , as man with many skills) up to full mains voltage , observing voltage at PSU ....... thinking about max cap voltage ( 25V as in FW ? ) , because with 0 Iq PSU is unloaded and voltage is maxed

if nothing is smelling - leave Variac at full mains ;

what's important - Iq must be very low , offset is irrelevant in this moment .

now turn one pot one turn ( assuming that you have multiturns )

then turn other pot one turn

observe Iq and offset

proceed one then second pot , again just one turn

observe Iq and offset

again one turn + one turn

now you are probably in range when you can see which pot is pulling offset in right direction - to 0 .

proceed iteratively with pots , while you set - say - 75% of desired Iq and zero offset

now - put lid on box and let it cook for a while - until yo get thermal equilibrium on heatsinks

it's best to use wire/clips to leave those voltmeters in place ;

open the lid , up bias to - say - 90% of desired one ,while maintaining offset

put lid on , let it cook

check ;

if all is OK - move voltmeters for Iq and offset to other channel and repeat procedure

use it few days at 90% of desired bias , then check and set to 100%

remember - temp. equilibrium with lid on is important

simple , isn't it ?

Project Modifications

Do you have some small modifications to suggest for the project that could improve it? Please list them and tell us why they improve the design. If this is discussed in a thread, please link the thread URL here....

Modification 1

Cross the streams!

Modification 2

Install a flux capacitor!


Reviews

Review 1

Review 2

Duuuude.....

Build Threads


F5 Build by 6L6
http://www.diyaudio.com/forums/pass-labs/182723-how-build-f5.html

F5 Build by CanAm Man
http://www.diyaudio.com/forums/pass-labs/183941-another-f5-build-beautiful-music-different-drummer.html

Planning an F5 build - some beginner questions
http://www.diyaudio.com/forums/pass-labs/137955-planning-f5-build-some-beginner-questions.html












Have you built this project? If so, please add the URL to the thread that you started to show off your build.














Related Group Buys

This page has been seen 6,882 times.

Hide this!Advertise here!

New To Site? Need Help?

All times are GMT. The time now is 09:09 AM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 80.00% / PHP 40.66%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio
"Wiki" powered by VaultWiki.
Wiki