USB to I2S 384Khz - DSD Converter - Page 112 - diyAudio
Go Back   Home > Forums > Commercial Sector > Vendor Forums > Vendor's Bazaar

Vendor's Bazaar Commercial Vendors large & small hawking their wares

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 6th January 2013, 12:32 AM   #1111
diyAudio Member
 
Join Date: Jan 2009
Location: Seattle, WA
Actually, you might want to take a look at this ...

Fix problems with programs that can't be installed or uninstalled

Cheers

Thomas
  Reply With Quote
Old 6th January 2013, 05:23 AM   #1112
diyAudio Member
 
Join Date: Jul 2005
Location: North IL
Received my board and installed it today! This started as a temp install in my dual mono BIII although it is quiet with no music playing with volume ramped up to full and sounds great with music playing. Temp in that I am not ready to remove and cut a square hole in back panel. Temp in that I only have a hi-res (24/96) vinyl rip of Bolero on the laptop…and vocals of left, right, both. I am using foobar and ASIO drivers.

I had installed a Neutrik type A/B USB panel mount connector when I built the DAC. I cut and spliced a USB cable omitting splicing the power wire as I don’t have any USB B connectors here. The Amanero board is powered by one half of a Twisted Pear LCDPS adjusted to 3.3v. If I mount the Amanero on rear panel I’ll remove the LDO….lighted magnifier work for me as it is tiny with SMD’s by it.

I used three lengths of small coax to connect the Amanero board to Sidecar. The three grounds are all connected to the Sidecar ground pin. I got this coax from some old S Video cables lying around.

The Teleporter on rear panel is used with a modded Denon 3910 that exports I2S/DSD. I’ll most likely add a TP OTTO 2 to switch between the two. An OTTO 2 corrects the DSD R and L channel swap in the Denon.

Nice work Domenico!
Attached Images
File Type: jpg amanero_usb_1_.jpg (131.3 KB, 730 views)

Last edited by SCompRacer; 6th January 2013 at 05:27 AM.
  Reply With Quote
Old 6th January 2013, 05:50 AM   #1113
qusp is offline qusp  Australia
diyAudio Member
 
qusp's Avatar
 
Join Date: Oct 2009
Location: Brisbane, Australia
nice one! however you really should twist your power wiring
  Reply With Quote
Old 6th January 2013, 06:00 AM   #1114
diyAudio Member
 
spavleski's Avatar
 
Join Date: Aug 2005
Location: Belgrade
Send a message via Skype™ to spavleski
Quote:
Originally Posted by amanero View Post
Yep it works with win8.

About the links i reported for info about this kind of error message, please don't download tools or other fix applications. Use the Windows DVD only to check and repair possible system errors.

Cheers,
Domenico
Confirmed :-)

Win 8 Refresh have done the job.

Thanks amanero.
Attached Images
File Type: jpg 1-6-2013 7-52-34 AM.jpg (90.3 KB, 699 views)
__________________
PSMLS CookBook by ZM
  Reply With Quote
Old 6th January 2013, 06:20 AM   #1115
diyAudio Member
 
Join Date: Jul 2005
Location: North IL
Quote:
Originally Posted by qusp View Post
nice one! however you really should twist your power wiring
Thank you qusp! I did twist the AC wiring, guess I was going for the Naim look with the DC....IIRC I've seen some of their stuff without the AC wires twisted.
  Reply With Quote
Old 6th January 2013, 07:16 AM   #1116
qusp is offline qusp  Australia
diyAudio Member
 
qusp's Avatar
 
Join Date: Oct 2009
Location: Brisbane, Australia
all wires should be twisted in their pairs, whether Naim does it or not =) I think you will find not doing it was a stylistic choice, rather than having any real purpose. if you can have them all run perfectly parallel you can still get some protection from noise, but just loosely bundled like that wont and even running parallel will have lower noise rejection than twisted.

Last edited by qusp; 6th January 2013 at 07:19 AM.
  Reply With Quote
Old 8th January 2013, 09:38 PM   #1117
diyAudio Member
 
Join Date: Aug 2010
Location: Italy
Just added to GB4.
  Reply With Quote
Old 11th January 2013, 03:03 PM   #1118
diyAudio Member
 
Join Date: Jun 2002
Location: Jakarta, Indonesia
I'm in GB4
  Reply With Quote
Old 11th January 2013, 04:45 PM   #1119
Sandor is offline Sandor  Italy
diyAudio Member
 
Join Date: Mar 2004
Location: Milan
Quote:
Originally Posted by ultrafi View Post
Been thinking of doing a PCM5102A based DAC board, essentially the same footprint as the Amanero board, and was wondering if there would be any interest in such a board?
I am interested in such a board.
Thank you.
  Reply With Quote
Old 11th January 2013, 06:24 PM   #1120
diyAudio Member
 
Join Date: Jan 2003
Location: LA
Acko is offering a group buy to a companion board, it is an isolator reclocker

Isolator group buy

Randy
__________________
My system is here
http://randytsuch-audio.blogspot.com/2005/10/my-system.html
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
HLLY USB SPDIF/ I2S CONVERTER kp93300 Digital Source 12 29th January 2012 02:55 PM
exaU2I - 32bit/384kHz Multi-Channel Asynchronous USB to I2S Interface exa065 exaDevices 0 11th November 2011 11:41 AM
$40 USB to I2S converter sharpi31 Digital Line Level 7 12th July 2009 04:09 PM


New To Site? Need Help?

All times are GMT. The time now is 11:41 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright ©1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2