diyAudio

diyAudio (http://www.diyaudio.com/forums/)
-   Vendor's Bazaar (http://www.diyaudio.com/forums/vendors-bazaar/)
-   -   KT88 SE Basic or Master Kit (http://www.diyaudio.com/forums/vendors-bazaar/180897-kt88-se-basic-master-kit.html)

scott17 10th January 2011 10:55 PM

KT88 SE Basic or Master Kit
 
FEATURES & SPECIFICATIONS:

Single-ended class A operation
Multiple output tube selection – KT88, 6550, EL34 (KT88 included with Master kit)
6N1P-EV preamplifier tube (included with Master kit)
5U4-GB rectifier tube (included with Master kit)
Switchable operation mode for output tubes:
Triode mode: 5+ watt output per channel (with KT88)
Ultralinear mode: 10+ watt output per channel (with KT88)
Conservative tube biasing allows for extended tube life without comprising sound quality.
No semiconductor devices are used in the construction of this amplifier.

The Basic Kit includes:

1 - Assembly/Layout Manual on CD with full-color photos

Resistors
2 - 220K 1/4W Metal Film 1%
2 - 100R 1W Metal Film 1%
4 - 1K 1/2W Metal Film 1%
2 - 1.5K 1W Metal Film 1%
2 - 47K 3W Metal Film 1%
1 - 2 - 560R 10W Wirewound 1%
1 - 10R 5W Wirewound 5%
2 - 1M 1/4W Metal Film 1%

Capacitors
1 - 30uF MP Oil
2 - 50uF MP Oil
2 - Erse or Solen 10uF 630V
2 - Erse 0.22uF 630V
2 - Elna Silmic II 100uF 25V
2 - Elna Silmic II 220uF 100V
1 - 0.1uF 400V MP Orange

Connectors, Switches, Etc.
1 - IEC Power Entry EMI/Fuse
1 - IEC Power Cord for 120V USA kit only
1 - Front Panel Power Switch
2 - Neutrik RCA Jack one red, one white
2 - Dual Binding Post
1 - DPDT Toggle Switch
1 - 9-Pin Socket
3 - 8-Pin Socket
2 - 2” Capacitor Clamp
1 - 1.5” Capacitor Clamp
2 - Turret Board
1 - Aluminum Knob
1 - 100K Alps Volume Control
1 - 2A or 2.5A Slow Blow Fuse - dependent on AC operating voltage
2 - Hammond 155H 5H Choke

Hardware
16 - 4-40 Locknut
32 - 4-40 x 1/4” Screw
8 - 6-32 Locknut
8 - 6-32 x 3/8” Screw
3 - 6-32 Lockwasher
16 - 8-32 Lockwasher w/transformers only
8 - 4-40 x 3/4” Standoff
1 - #4 Ground Lug
1 - #6 Ground Lug
Crimp Terminal RED .187” 2 w/(120V kit) 4 w/(240V kit)
2 - Crimp Terminal RED .250” 2
Crimp Terminal BLU .187” 2 w/(120V kit) 0 w/(240V kit)
Crimp Splice 0 w/(120V kit) 1 w/(240V kit)
4 - Adhesive Tie Wrap Mount
12 - Tie Wrap
2 - Velcro Strip
1/8” Heatshrink Tubing - 18 inches
1 - 1.5mm Hex Key Wrench

All required wire.

Additional components included with the Master kit:
1 – Pre-punched Aluminum Chassis with Walnut Side Panels
1 – Aluminum bottom plate w/(4) #6 x 1/2” sheet metal screw

1 – PT750 Power Transformer w/mounting bolts & insulators
120/240V primary, 50/60Hz
750V, 200mA, center-tapped secondary
6.3V, 5A, center-tapped secondary
5V, 3.5A, center-tapped secondary

1 – Filter Choke w/mounting bolts & insulators
10 Henry, 200mA, rated at 500V

2 – Output Transformer w/mounting bolts & insulators
5000 ohm primary with 6 ohm secondary load
20-20,000Hz flat frequency response across band
120mA, 500V rated primary, 25 watt output

3 – 4.5” X 3.75” Powder-coated transformer end bell
1 – 3.75” x 3.125” Powder-coated transformer end bell

2 – Electro-Harmonix KT88EH Power Vacuum Tube
1 – Electro-Harmonix 5U4GB Rectifier Vacuum Tube
1 – Russian NOS 6N1P-EV Driver Vacuum Tube

Basic Kit $299.00 USD + shipping
Master Kit $849.00 USD + shipping

The Basic Kit is shipped in a USPS Large Flat Rate Box @ approx. 7 lbs.
The Master Kit is shipped via USPS in (3) boxes, 1 @ 11 lbs, and 2 @ 20 lbs. each.

scott17 10th January 2011 10:59 PM

KT88 SE Basic or Master Kit Photos
 
2 Attachment(s)
I currently have 10 Basic Kits available for sale.

The transformers and chassis will be available in 2 - 4 weeks at which time I will have 25 full Master Kits available for sale.

The photos of the completed amp are attached.

scott17 13th January 2011 05:20 PM

Chassis Depth
 
An important fact about the Basic Kit.

If you are providing your own chassis, make sure that it is at least 17"W X 10"D X 3"H.

If you would like to order, send a PM with your PayPal email and your shipping address. I will send a PayPal invoice.

Thanks,

Scott

scott17 13th January 2011 06:45 PM

Quote:

Originally Posted by scitizen17 (Post 2431987)
An important fact about the Basic Kit.

If you are providing your own chassis, make sure that it is at least 17"W X 10"D X 3"H.

If you would like to order, send a PM with your PayPal email and your shipping address. I will send a PayPal invoice.

Thanks,

Scott

One other important fact that I did not intend to be remiss in reporting:

If you're providing your own transformers, please pay attention to the transformer specifications as shown on the Master Kit transformer list.

Scott

scott17 14th January 2011 11:48 AM

Quote:

Originally Posted by scitizen17 (Post 2432078)
One other important fact that I did not intend to be remiss in reporting:

If you're providing your own transformers, please pay attention to the transformer specifications as shown on the Master Kit transformer list.

Scott

If you are providing your own chassis, the hardware included in the Basic Kit will work with chassis top plate thickness of up to 0.125".

Dave R 21st January 2011 08:34 PM

I picked up my kit at the post office this morning. Everything looks great.

I've got some fabrication to do before I can start assembling, and it will be a few more weeks before I get my transformers, so that's gonna drive me nuts! :D

Thanks, Scott for making this available to everyone. I'm really looking forward to getting this up and running.

scott17 30th January 2011 07:33 PM

Input/Output Measurements
 
1 Attachment(s)
I have attached a chart with input/output voltage readings taken for this amplifier. I took readings for both 8 ohm & 5 ohm loads in both the triode & UL modes. The input and corresponding output voltage readings were taken at the level right before clipping of the output waveform. The volume control was set for minimum resistance, fully clockwise. The input signal level was adjusted on the function generator. The output readings were taken across the speaker terminals. Resistive dummy loads were used on the amplifier output.

noodle 30th January 2011 08:39 PM

Any update on the availability of the full kit??

scott17 30th January 2011 09:23 PM

Quote:

Originally Posted by noodle (Post 2451815)
Any update on the availability of the full kit??

The final shipment of power transformers will be delivered tomorrow. The chassis were supposed to be shipped the week of 1/24/10. I'm hoping to have them at least by the first of next week, then I'm ready to ship.

scott17 1st February 2011 02:21 AM

Update
 
I have sold 3 of the 10 Basic parts kits I currently have for sale.

25 Master Kits will be available for sale starting 2/7/2011.


All times are GMT. The time now is 04:16 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio


Content Relevant URLs by vBSEO 3.3.2