Tas5630+smps+aluminum case finished!new year coming!

[bayensf]

Originally Posted by soren5

Hello Fred,

I have two G300v21 boards, which are similar to the G300D, but wihtout the DSP (as far as I understand). The quality of PCB, parts, and overall assemply seems very good for the price IMO. I've not done intensive listening, but my immediate impression is that they sound really good, powerful and clean, and with very low noise floor.

With regards to the DSP, I think that Sinewave is using SigmaDSP and this seems to require a quite expensive USB device in order to configure the board. But perhaps you know more about this than I do?

Soren

Hi Soren ,

Yes it's SigmaDSP , but expensive is a relative word, it's about 200 Euro. I don't have it but I played around with the software. It was pretty cool. Anyway I am still looking for a 3 (2*) or 6 channel class d amp.

Yes

[forart.eu]

Originally Posted by bayensf

Anyway I am still looking for a 3 (2*) or 6 channel class d amp.

Check out the DARED DV-6C then !

[Kjeldsen]

Originally Posted by bayensf

Hi Soren ,

Yes it's SigmaDSP , but expensive is a relative word, it's about 200 Euro. I don't have it but I played around with the software. It was pretty cool. Anyway I am still looking for a 3 (2*) or 6 channel class d amp.

Yes

200 Euro is almost the price for a Behringer NU1000DSP, so I consider this expensive. Didn't know that getting to the DSP in a Sinewave DSP amp would be that expensive

[migafirma]

Hello all, Someone know if it possible to have (probably by using SigmaStudio or others tools) real time control on crossovers frequency, parametric EQ and volume by a serial communication canal on G300DD ? Migmha

[authlxl]

Originally Posted by migafirma

Hello all, Someone know if it possible to have (probably by using SigmaStudio or others tools) real time control on crossovers frequency, parametric EQ and volume by a serial communication canal on G300DD ? Migmha

Mickel, we upload block digram picture here, you can real time control it by Sigma Studio software through USBI downloader or you can use one MCU real time control it by I2C with same port.

I2S digital format is 24bit slave mode, DSP is master.

[migafirma]

Very good, all is on board inluding USBi adaptor. I contact you to buy it. Thanx Migmha

[bayensf]

Originally Posted by forart.eu

Check out the DARED DV-6C then !

I don't think it can beat the Class D AMPS from (C)SINEWAVE. Looking at this DV-6C AMP it seems also that the Subwoofer channel has different audio signal pass through than the other 5 channels.

So I think this can not work to drive my speakers,

anyway thanks for the reply.

[Veda]

Originally Posted by authlxl

G36d new amp can works at high/mid/low 3way or 2.1CH mode, about sub amp,one tas5630 PBTL support and loader low to 2ohm. DSP and two tas chip osc sync from one active OSC.

I wish I read this sooner as I just ordered a G33D
So the G36D is exactly the same as G33D but with more power?

[authlxl]

Originally Posted by Veda

I wish I read this sooner as I just ordered a G33D
So the G36D is exactly the same as G33D but with more power?

ok! g36d is high power level version, 3ch and 600w rms power level.

[Veda]

Originally Posted by authlxl

ok! g36d is high power level version, 3ch and 600w rms power level.

Will it has remote as well? If it has remote it'll be the perfect advanced integrated amp.