Cheap printed circuit boards starting with 0,0375 Euro / cm2

[KatieandDad]

What is the maximum board size you can produce ?

I'm after some that are 500mm x 160mm with some very detailed 0.2mm parallel traces. There are a lot of between pad tracks too.

 

[msdesigner]

The presented DEMO BOARD , has 40 x 30 mm.........but I can make also smaller.
But any boards ( single layer ) , under 67 cm2 has a flat cost : 2,5 Euro / board.

Can not be many boards on the same panel ( because could be pads and traces errors)

What is the maximum board size you can produce ?

 

[KatieandDad]

Far too small for my requirements - sorry.

 

[msdesigner]

Sorry !!! .......I had in mind that you talk about smaller size .......... now I saw.

So 500 x 160 ....is OK ! for me.

Please send the file of pcb 500x 160 by e-mail.
Is very difficult to tell you the price , because is not depend only of board size.

Far too small for my requirements - sorry.

 

[msdesigner]

Sorry !!! .......I had in mind that you talk about smaller size .......... now I saw.

So 500 x 160 ....is OK ! for me.

Please send the file of pcb 500x 160 by e-mail.
Is very difficult to tell you the price , because is not depend only of board size.

 

[msdesigner]

Printed circuit board , from very bad .jpeg quality (96 dpi) , with thin traces = 0,15 mm !!!

 

[msdesigner]

Tinned printed circuit board on CEM3 support.
As standard boards CEM3 has 25-35 um

FR4 = 16 - 24 um

 

[slr 5000]

hi
can you make me some boards using the schematic on this link

http://www.amplimos.it/images/V-fet complementary 2SK82_2SJ28_Ver_B.bmp

regards Sheafer

 

[msdesigner]

Only if you have the pcb , ready to be made. ( jpeg 600 dpi at least , pdf , ExpressPCB , Eagle , DipTrace ) ..............

If you will go to 320volt.com you'll find very nice projects for MOS-FET amps , complete with pcb's

DXBlame sound very nice

Look there , choose the project with pcb, and send it to my e-mail address.


Regards,

Mihai

hi
can you make me some boards using the schematic on this link

http://www.amplimos.it/images/V-fet complementary 2SK82_2SJ28_Ver_B.bmp

regards Sheafer

 

[msdesigner]

Printed circuit boards - tinned - traces 0,15 mm , holes 0,5 mm

 

[msdesigner]

Very cheap Printed circuit board

 

[msdesigner]

Printed circuit board , traces 0,1 - 0,2 mm , pad thickness 0,1 - 0,2 mm

 

[msdesigner]

Very cheap printed circuit board, can be found in below picture.

An externally hosted image should be here but it was not working when we last tested it.

 

[msdesigner]

Tinned PCB on FR4 support.

An externally hosted image should be here but it was not working when we last tested it.

 

[msdesigner]

Tinned printed circuit boards (PCB) - FR4

An externally hosted image should be here but it was not working when we last tested it.

 

[msdesigner]

Cheapest PRINTED CIRCUIT BOARDS on FR4 support
( as optional : TINING , SILKSCREEN )

 

[msdesigner]

Tinned printed circuit board on CEM3 support.

 

[msdesigner]

Tinned printed circuit board on CEM3 support.

 

[msdesigner]

Tinned PCB - printed circuit board on FR4 (fiberglass)

An externally hosted image should be here but it was not working when we last tested it.

 

[RCruz]

I just placed a free PCB layout on mjy website after some requests. The Gerbers are attached. Can people get such PCBs from you, what price?

jan

No answer ?