4:1 or 4:2 mux.... - Page 4 - diyAudio
Go Back   Home > Forums > Commercial Sector > Manufacturers > Twisted Pear

Twisted Pear Superior quality electronic kits

Reply
 
Thread Tools Search this Thread
Old 29th June 2013, 06:08 PM   #31
diyAudio Member
 
mavallarino's Avatar
 
Join Date: Oct 2006
4:1 receiver with the current source.
Power seems ok but the receiver can't lock the signal, not coax nor tos link

Pics were uploaded on your forum a couple of months ago.
Thanks!

Inviato dal mio GT-I9000 con Tapatalk 2
  Reply With Quote
Old 3rd July 2013, 08:18 AM   #32
diyAudio Member
 
mavallarino's Avatar
 
Join Date: Oct 2006
Hi Russ,
Have you had the chance to look over the photos?
Thanks
  Reply With Quote
Old 3rd July 2013, 12:50 PM   #33
diyAudio Member
 
Russ White's Avatar
 
Join Date: Jan 2005
Location: Nashville, TN, USA
Send a message via Yahoo to Russ White
Mavallarino this module (the subject of this thread) does not even exist for anyone other than me yet, so I am not sure what you want me to look at... Is it a SPDIF 4 (which is a quad level shifter)? If you have a thread on the support forum, just reply so it bubbles up to the top, and I will look at it for you.

Cheers!
Russ
__________________
Less pulp more juice Twisted Pear Audio.
  Reply With Quote
Old 31st July 2013, 07:52 AM   #34
diyAudio Member
 
Join Date: Dec 2004
Location: Roma
Dear Russ,
is it kindly possible to know approximately when the the 4:1 Mux for Buffalo III SE will be ready?

Thanks a lot!

GM
  Reply With Quote
Old 31st July 2013, 11:29 AM   #35
diyAudio Member
 
Russ White's Avatar
 
Join Date: Jan 2005
Location: Nashville, TN, USA
Send a message via Yahoo to Russ White
The design is finished and will be included in the next board order which will be in a week or two.

Cheers!
Russ
__________________
Less pulp more juice Twisted Pear Audio.
  Reply With Quote
Old 3rd October 2013, 11:52 AM   #36
RollE2k is offline RollE2k  Sweden
diyAudio Member
 
Join Date: Nov 2007
Russ: When will the boards be avalible? Have been waiting for these quite a while now :-)
  Reply With Quote
Old 4th October 2013, 12:51 PM   #37
diyAudio Member
 
mavallarino's Avatar
 
Join Date: Oct 2006
Hi Russ,
I sent in the photos using the feedback (AT) address.
Have you had the chance to look them over?

I can have the boards shipped to you if you are able to test them.
Please let me know.

Best
  Reply With Quote
Old 4th December 2013, 05:30 PM   #38
diyAudio Member
 
Join Date: Dec 2004
Location: Roma
Dear Russ,
any update about availability?

Meanwhile: to switch between 4 spdif for the - BIII SE - do you reccommend to buy:

- the "old" MUX 4:1 CS8416 or
- the BIII 4-Channel S/PDIF Level Converter or

...better to wait this dedicated one when ready?

Thanks!
best regards,
GM

Last edited by gianmaria; 4th December 2013 at 05:39 PM.
  Reply With Quote
Old 4th December 2013, 05:35 PM   #39
diyAudio Member
 
BrianDonegan's Avatar
 
Join Date: Dec 2004
Location: TPA HQ
Quote:
Originally Posted by gianmaria View Post
Dear Russ,
any update about availability?

Meanwhile to switch between 4 spdif to the - BIII SE - do you reccommend to buy:

- the "old" MUX 4:1 CS8416
- the 4-Channel S/PDIF Level Converter of the BIII?

...or... better to wait this dedicated one ready?

thx,
best regards,
GM
The "4-Channel S/PDIF Level Converter of the BIII" is not a switch. It simply converts four channels of consumer-level S/PDIF to TTL-level S/PDIF.
__________________
Twisted Pear Audio
  Reply With Quote
Old 4th December 2013, 09:07 PM   #40
diyAudio Member
 
Russ White's Avatar
 
Join Date: Jan 2005
Location: Nashville, TN, USA
Send a message via Yahoo to Russ White
I had to pull the original order (because of a design change), but I just ordered a batch of 4:1 mux boards. They will be here in a couple weeks.
__________________
Less pulp more juice Twisted Pear Audio.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Has anyone tried MINIDSP between Buffalo II and MUX? dublin78 Twisted Pear 0 31st January 2012 02:54 PM
Sdpif MUX Ryssen Digital Line Level 1 8th August 2011 12:53 AM
Attenuator and MUX chips. GK Solid State 0 18th September 2009 07:06 AM
Simple Audio Mux LMC13 Solid State 4 25th April 2006 06:52 PM
mux two input to one... MaXiZ Solid State 4 6th February 2004 10:03 AM


New To Site? Need Help?

All times are GMT. The time now is 03:19 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2