My thoughts on miniature coaxial RF connectors - diyAudio
Go Back   Home > Forums > Commercial Sector > Manufacturers > Twisted Pear

Twisted Pear Superior quality electronic kits

Reply
 
Thread Tools Search this Thread
Old 7th July 2012, 04:08 PM   #1
diyAudio Member
 
Russ White's Avatar
 
Join Date: Jan 2005
Location: Nashville, TN, USA
Send a message via Yahoo to Russ White
Default My thoughts on miniature coaxial RF connectors

Hi Folks,

This topic has come up quite a few times. Yesterday and today a few of your folks brought it up again anew.

Some people like the idea of using the miniature coaxial RF connectors such as for board to board signal connections - especially for very high speed signals such as master clocks etc. I don't necessarily see any reason to disagree with them.

For example: IPX, UMCC, U.FL and a few others that are for the most part compatible are popular choices.

These shielded coaxial connectors/cables are designed for very high bandwidth applications and (importantly) 50-ohm termination. One typical use is for WiFi connections from modules to antennae in notebook computers etc. This makes perfect sense, but the 50-Ohm termination is pretty critical in achieving this kind of bandwidth. Without that 50-ohm termination you will not achieve anything like the maximum bandwidth. The intended use is definitely not TTL level signals from all that I have read, but I could be wrong here so if someone knows where a manufacturer says otherwise I would really appreciate a link.

Still - I truly think it quite likely that even with TTL level signals and higher impedance loads those connectors will definitely still work just fine. It is just you will get the typical coax reflections common with impedance mismatches. I personally have tried them a couple of years back, but I found that there were some practical DIY considerations for not relying on them solely for module connectivity. I also personally did not see any improvement at the time. The DAC already measured so well I was not interested in changing anything that could negatively impact that. That said - I also was weighing other factors more related to builder experience and "DIYability".

A couple of those factors:
  • First there is a lot less flexibility in wiring options - with the coax you must use predefined length female cables, or make them yourself which is not trivial.
  • Higher cost, for something that not every builder may even want. This can be a very real barrier for people.
  • Reliability - the female connectors are not designed for repeated installation and removal which is something DIY folks can do a lot of. They soon (maybe a half dozen cycles) must be replaced if not left in place.

So I see that some people still want to use them, which quite honestly I think could definitely be worthwhile. In fact I have learned at least one user created a small adapter board for the Buffalo III. This is something I wholeheartedly encourage. This is why it is a DIY module.

So when I checked my email again this morning and had about a half dozen requests that I think about a way to support these connectors ourselves for modules that we produce. Not just for B-III either, but other modules as well.

I am open to the idea, but I want to get a feel for how you folks as users feel about the idea, and try to come up with a good strategy for supporting this style of connection.

My thinking is that modules should be flexible. If a builder wants to use mini coax I would like to support it, but not at the expense of other forms of connection. In other words I don't want that to be the only choice.

With that in mind - I have a few potential lines of action I would like to discuss.
  • Would you folks be interested in a adapters for various modules? B-II, B-III,Opus, COD, SPDIF MUX, etc... If so we could offer boards very cheaply. Just what it takes to cover costs.
  • Would you also like to see optional male connectors on new modules? For example I am thinking of adding them to the USB module and possibly others.

I would really like to get some community feedback on how to proceed and if you all even think it worthwhile to consider at this point.

I personally think it is a good idea to support it - as long as it is completely optional. In some cases the shielding factor alone could improve build results. Especially when you need to be creative with module location.

I am listening.

Let the public discussion begin! Please respond with your thoughts and opinions on my proposals.

Cheers!
Russ
__________________
Less pulp more juice Twisted Pear Audio.

Last edited by Russ White; 7th July 2012 at 04:22 PM.
  Reply With Quote
Old 7th July 2012, 04:24 PM   #2
diyAudio Member
 
Join Date: Feb 2009
Location: Brisbane, Australia
I would use an adapter on my Opus, if you offered one I would buy it.

To be honest I would still prefer to have these connectors onboard as the default option. The expense of the cables is small relative to the rest of the system in the majority of cases and provides sufficient improvement to justify it.

Last edited by hochopeper; 7th July 2012 at 04:30 PM.
  Reply With Quote
Old 7th July 2012, 04:30 PM   #3
avr300 is offline avr300  Denmark
diyAudio Member
 
avr300's Avatar
 
Join Date: Sep 2005
Location: DK
Those connectors are crap. As you says they are not intended to be used. Once maybe twice - and no more.

As one of my customers who produces cables for a living once said - "it the worst connector ever invented".

That was just my opinion.
  Reply With Quote
Old 7th July 2012, 04:38 PM   #4
diyAudio Member
 
Join Date: Jul 2010
Default u.fl

Russ: I added a u.fl jack to my B-II board for masterclock connection, and ran a 5 cm u.fl cable from my USB interface to the B-II. I prefer the sound with synchronous clocking this way, have had no problems with the u.fl scheme, and conceptually "think" it is a good way to go. I do not have the ability to make any measurements though.
I know diyaudio member "Lorien" made some measurements of standard pin headers carrying high speed clock signals, and did not like what he saw in comparison to u.fl.

I do not suspect that adapters from pin header to u.fl is the answer though, as that just combines two contacts, and will still have the distortions inferent in the pin headers.

I would prefer to see u.fl micro BNCs right on the boards, adapters seem to compromised to me as they just add another connection on each end.

As to the reliability of connection cycles with u.fl, this does not concern me, as replacing the micro BNCs is not too difficult with an iron and a steady hand. Additionally, the expense it is not an issue, as the cables and jacks are just not really expensive in the big picture of putting together a really good DAC based on TPA kits.

So my preference would be for micro BNCs right on the boards (B-III, USB receiver, etc). The u.fls are pretty easy to purchase from Mouser/Digikey, and in many different lengths. For TPA, is would be nice if the micro BNC jacks were positioned (on the boards) such that a good layout would allow for 5 cm u.fl cables.

addendum: actually, maybe adapters could be a good idea as well, if they were designed such that they could (optionally) be soldered in place via very short pins (or bits of solid core wire) instead of plug in via pin headers (or IDC, etc).

Last edited by barrows; 7th July 2012 at 04:46 PM.
  Reply With Quote
Old 7th July 2012, 04:40 PM   #5
diyAudio Member
 
Russ White's Avatar
 
Join Date: Jan 2005
Location: Nashville, TN, USA
Send a message via Yahoo to Russ White
Quote:
Originally Posted by barrows View Post
I do not suspect that adapters from pin header to u.fl is the answer though, as that just combines two contacts, and will still have the distortions inferent in the pin headers.

I would prefer to see u.fl micro BNCs right on the boards, adapters seem to compromised to me as they just add another connection on each end.

As to the reliability of connection cycles with u.fl, this does not concern me, as replacing the micro BNCs is not too difficult with an iron and a steady hand. Additionally, the expense it is not an issue, as the cables and jacks are just not really expensive in the big picture of putting together a really good DAC based on TPA kits.

So my preference would be for micro BNCs right on the boards (B-III, USB receiver, etc). The u.fls are pretty easy to purchase from Mouser/Digikey, and in many different lengths. For TPA, is would be nice if the micro BNC jacks were positioned (on the boards) such that a good layout would allow for 5 cm u.fl cables.
Actually adapters need not be any real compromise at all, because you can directly solder them to the board and very solidly connect the signal just as if it were a trace. There is no interface other than the solder and copper necessary.

This would very effectively mate the adapter the board and the ground plane.

This would be very much equivalent to having it on the board. For those with existing modules it would work very nicely indeed.
__________________
Less pulp more juice Twisted Pear Audio.

Last edited by Russ White; 7th July 2012 at 04:44 PM.
  Reply With Quote
Old 7th July 2012, 04:46 PM   #6
diyAudio Member
 
Russ White's Avatar
 
Join Date: Jan 2005
Location: Nashville, TN, USA
Send a message via Yahoo to Russ White
Here is an example I worked up this morning. One could directly solder this to a B3. No header needed at all. It effectively becomes integral to the circuit.
Attached Images
File Type: jpg pcb.jpg (32.0 KB, 489 views)
__________________
Less pulp more juice Twisted Pear Audio.
  Reply With Quote
Old 7th July 2012, 04:51 PM   #7
Can you say Audio?
diyAudio Member
 
Join Date: Aug 2011
Location: Aurora, Colorado
I love it Russ. u.fl seems a much better digital interconnect.
  Reply With Quote
Old 7th July 2012, 04:54 PM   #8
diyAudio Member
 
Join Date: Jul 2010
Default Yeah...

Quote:
Originally Posted by Russ White View Post
Here is an example I worked up this morning. One could directly solder this to a B3. No header needed at all. It effectively becomes integral to the circuit.
Russ, right on! I had just added an addendum to my post as you were posting this. Agreed, I woud love to this for the B-II as well, thanks, looks great to me.
  Reply With Quote
Old 7th July 2012, 04:57 PM   #9
diyAudio Member
 
Russ White's Avatar
 
Join Date: Jan 2005
Location: Nashville, TN, USA
Send a message via Yahoo to Russ White
Quote:
Originally Posted by avr300 View Post
Those connectors are crap. As you says they are not intended to be used. Once maybe twice - and no more.

As one of my customers who produces cables for a living once said - "it the worst connector ever invented".

That was just my opinion.
I value that opinion.

One user who is also a motherboard engineer for Asus (name omitted to protect the innocent) echoed that thought.

He also stressed that it is important to adhere to the pattern footprint and not have *any* copper directly under the pin section of the male header. Not even the ground plane. In looking at some layouts can see a few designers may have missed that point.
__________________
Less pulp more juice Twisted Pear Audio.
  Reply With Quote
Old 7th July 2012, 05:02 PM   #10
diyAudio Member
 
Join Date: Jul 2010
Default The question would be:

Quote:
Originally Posted by Russ White View Post
I value that opinion.

One user who is also a motherboard engineer for Asus (name omitted to protect the innocent) echoed that thought.

He also stressed that it is important to adhere to the pattern footprint and not have *any* copper directly under the pin section of the male header. Not even the ground plane. In looking at some layouts can see a few designers may have missed that point.

In comparison to what? As mentioned, "Lucien" looked at clock signals I found that u.fl had better signal integrity than a standard pin header, maybe there is something else which would be better than u.fl, but it does appear thta u.fl outperforms standard pin headers for high speed signals...
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Laser Pickup´s M52103FP RF-Amp instead of older CX20109 RF-Amp Salar Digital Source 2 25th July 2010 05:44 PM
Miniature sub controller PWatts Subwoofers 1 13th May 2008 10:21 PM
Looking for a Miniature 24V relay AKSA Parts 2 18th July 2003 08:22 AM
Miniature ESL BennySP Planars & Exotics 9 10th June 2002 06:23 PM


New To Site? Need Help?

All times are GMT. The time now is 02:58 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright ©1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2