Buffalo III - flexibility without compromise. - Page 73 - diyAudio
Go Back   Home > Forums > Commercial Sector > Manufacturers > Twisted Pear

Twisted Pear Superior quality electronic kits

Reply
 
Thread Tools Search this Thread
Old 12th October 2011, 01:52 PM   #721
4est is offline 4est  United States
diyAudio Member
 
Join Date: Sep 2009
Location: Grand Rapids, Mi
Default not that part

"Originally Posted by Russ White View Post
Something like this would work just fine:

15-44-5820 Molex Headers & Wire Housings

Then just a 2 x 10 2.54mm pitch standard male pin header for the other side."

This part is not the one that came with the kit, but something that can be used instead of the ribbon cable system.
  Reply With Quote
Old 12th October 2011, 02:11 PM   #722
diyAudio Member
 
BrianDonegan's Avatar
 
Join Date: Dec 2004
Location: TPA HQ (The Basement)
Quote:
Originally Posted by necplusultra View Post
can somebody confirm that this is the replacement part for the ribbon connector for sidecar

thanks.
http://www.molex.com/webdocs/datashe...R_TRP_CONN.pdf
You have PM
__________________
Twisted Pear Audio
  Reply With Quote
Old 12th October 2011, 02:13 PM   #723
diyAudio Member
 
Join Date: Jul 2008
Location: Lviv
I think this should fit also:
http://eu.mouser.com/ProductDetail/O...yoW1MVuri0I%3d


Does anybody know how to connect following PCM signal: MCLK, LRCK1, LRCK2, SCLK1, SCLK2, SDIN1, SDIN2, SDIN3, SDIN4 to appropriate BIII input?
__________________
If for pristine and pure adoration - it's diyAudio dedication!

Last edited by AndriyOL; 12th October 2011 at 02:38 PM.
  Reply With Quote
Old 12th October 2011, 07:19 PM   #724
LeonvB is offline LeonvB  Netherlands
diyAudio Member
 
Join Date: May 2010
Location: Netherlands
I think 3M connectors are used. Also I'll update the guide to include a full range of suitable Molex and possibly 3M connectors for those that need replacement numbers.
  Reply With Quote
Old 12th October 2011, 07:22 PM   #725
diyAudio Member
 
BrianDonegan's Avatar
 
Join Date: Dec 2004
Location: TPA HQ (The Basement)
I am actually going to be offering additional connectors in the Parts Bin. This will include various connectors used throughout our product line.
__________________
Twisted Pear Audio
  Reply With Quote
Old 12th October 2011, 07:30 PM   #726
diyAudio Member
 
merlin el mago's Avatar
 
Join Date: Sep 2009
Location: Catalonia - Europe
Brian you have PM about aerial female ribbon connectors
  Reply With Quote
Old 12th October 2011, 07:47 PM   #727
LeonvB is offline LeonvB  Netherlands
diyAudio Member
 
Join Date: May 2010
Location: Netherlands
Just updated the guide to 1.0.3: expanded the IDC part list, to include both 20 and 24 pin Molex and 3M partnumbers (for both Digikey and Mouser where possible), plus I added the board-to-board connectors mentioned earlier in this thread. For the rest just a few minor changes to clarify some things.
  Reply With Quote
Old 13th October 2011, 05:29 PM   #728
diyAudio Member
 
Join Date: Jul 2008
Location: Lviv
Hi Leon,
Are you familiar with what I asked?
__________________
If for pristine and pure adoration - it's diyAudio dedication!
  Reply With Quote
Old 13th October 2011, 05:56 PM   #729
LeonvB is offline LeonvB  Netherlands
diyAudio Member
 
Join Date: May 2010
Location: Netherlands
Page 14 of the manual says it should be this:
MCLK = do not connect (master clock not connected on either BII or BIII)
SCLK1 or SCLK2 = BCK (SCLK = serial clock = bit clock)
LRCK1 or LRCK2 = D1 (LRCK = Word clock)
SDIN1, SDIN2, SDIN3, SDIN4 = D2 to D5
  Reply With Quote
Old 13th October 2011, 06:46 PM   #730
diyAudio Member
 
Join Date: Jul 2008
Location: Lviv
Quote:
Originally Posted by LeonvB View Post
Page 14 of the manual says it should be this:
MCLK = do not connect (master clock not connected on either BII or BIII)
SCLK1 or SCLK2 = BCK (SCLK = serial clock = bit clock)
LRCK1 or LRCK2 = D1 (LRCK = Word clock)
SDIN1, SDIN2, SDIN3, SDIN4 = D2 to D5
Shall I tie together SCLK1 and SCLK2, LRCK1 and LRCK2 to connect to appropriate pins of BIII?
Source GND to BIII GND or it's not obligatory, as GND isn't I2S bus line and es9018 datasheet shows connections only for PCM serial data, fame clock (word clock), and bit clock?
__________________
If for pristine and pure adoration - it's diyAudio dedication!

Last edited by AndriyOL; 13th October 2011 at 07:06 PM.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Legato or IVY III outputs for Buffalo II? natzev_i Twisted Pear 272 21st March 2011 09:08 PM
Buffalo Dac original vs Buffalo II mrtakib Digital Line Level 7 24th August 2010 07:47 AM
How much compromise, small EQ'ed sub audiobomber Subwoofers 10 15th March 2007 10:46 PM
Considering a compromise mashaffer Full Range 7 15th May 2006 12:45 AM
OB subs: Best compromise? MtnBob Subwoofers 13 26th May 2004 03:19 PM


New To Site? Need Help?

All times are GMT. The time now is 03:45 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright ©1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2