Buffalo III - flexibility without compromise. - Page 55 - diyAudio
Go Back   Home > Forums > Commercial Sector > Manufacturers > Twisted Pear

Twisted Pear Superior quality electronic kits

Reply
 
Thread Tools Search this Thread
Old 10th September 2011, 08:55 AM   #541
diyAudio Member
 
Join Date: Jun 2011
Quote:
Originally Posted by Russ White View Post
In the next month or so. I am planning on ordering them soon, then we just need to give them a quick test.
Thanks for quick reply. It's important to me, because i dont' have enough room in my enclosure for 4spdif board.
Can you tell me dimensions of this little 1spdif board? It will be stacked over another board (B3) or not?
  Reply With Quote
Old 10th September 2011, 04:32 PM   #542
Horio is offline Horio  United States
Newbie
diyAudio Member
 
Horio's Avatar
 
Join Date: Mar 2010
Location: Seattle
Quote:
Originally Posted by marcinpoz1qaz View Post
Thanks for quick reply. It's important to me, because i dont' have enough room in my enclosure for 4spdif board.
Can you tell me dimensions of this little 1spdif board? It will be stacked over another board (B3) or not?
I believe the single SPDIF board has the same footprint as the old B2 board, so it should stack nicely over your B3/IVY stage.

SPDIF Board Layout
  Reply With Quote
Old 10th September 2011, 04:41 PM   #543
diyAudio Member
 
BrianDonegan's Avatar
 
Join Date: Dec 2004
Location: TPA HQ
Quote:
Originally Posted by Horio View Post
I believe the single SPDIF board has the same footprint as the old B2 board, so it should stack nicely over your B3/IVY stage.

SPDIF Board Layout
You are thinking of the S/PDIF receiver module. This board will be quite small; roughly a third the size of the 4input module.
__________________
Twisted Pear Audio
  Reply With Quote
Old 10th September 2011, 07:57 PM   #544
avr300 is offline avr300  Denmark
diyAudio Member
 
avr300's Avatar
 
Join Date: Sep 2005
Location: DK
Why all this moderation in this threat ?

I know it's manufactures "gallery", however the information (missing) is by no mean toe-stepping on TPA. Perhaps it's even good information ?

I just wonder ?
  Reply With Quote
Old 10th September 2011, 07:58 PM   #545
diyAudio Member
 
Russ White's Avatar
 
Join Date: Jan 2005
Location: Nashville, TN, USA
Send a message via Yahoo to Russ White
We keep the moderation to a minimum, but in this case a post was deleted because I had directed that that sort of post should be in its own thread, and I gave prior warning.

I also do not happen to believe it is good information because it does not jibe with prior measured nor experienced results.

There is no other reason beyond that.
__________________
Less pulp more juice Twisted Pear Audio.

Last edited by Russ White; 10th September 2011 at 08:06 PM.
  Reply With Quote
Old 11th September 2011, 05:47 PM   #546
diyAudio Member
 
pmchoong's Avatar
 
Join Date: Jan 2008
Location: Kuala Lumpur
Default LEDs

Hi

I am soldering the components to the BIII and other boards. Now, shouldn't the LEDs '+' (the longer leg) goes into the square pad? But on the silkscreen, the flat side of the LED is the '-' of the LED. I have now soldered all my LEDs '+' to the square pads when I noticed the flat side of the LEDs. Should I reverse all of these??

Thanks.
  Reply With Quote
Old 11th September 2011, 06:42 PM   #547
diyAudio Member
 
Join Date: Jul 2009
Location: S.F. Bay Area
Please reverse all of them! The flat side is "-". Reversed LED would not work.

Good luck,
Milton
  Reply With Quote
Old 11th September 2011, 07:05 PM   #548
diyAudio Member
 
pmchoong's Avatar
 
Join Date: Jan 2008
Location: Kuala Lumpur
Thanks. I always thought that the square pad is for the '+'.
  Reply With Quote
Old 12th September 2011, 12:34 AM   #549
angcl is offline angcl  Singapore
diyAudio Member
 
Join Date: Aug 2005
I had BIII and 4-Channel S/PDIF (or AES-EBU) Input Module ,not sure how to set the SW1 & SW2 ? leave it as factory defualt ? all off mode ?
  Reply With Quote
Old 12th September 2011, 02:43 AM   #550
Banned
 
Join Date: Jul 2005
Location: Pukekohe, New Zealand
Quote:
I had BIII and 4-Channel S/PDIF (or AES-EBU) Input Module ,not sure how to set the SW1 & SW2 ? leave it as factory defualt ? all off mode ?
Did you try reading the manual? I found all the switch settings were in there.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Legato or IVY III outputs for Buffalo II? natzev_i Twisted Pear 272 21st March 2011 08:08 PM
Buffalo Dac original vs Buffalo II mrtakib Digital Line Level 7 24th August 2010 06:47 AM
How much compromise, small EQ'ed sub audiobomber Subwoofers 10 15th March 2007 09:46 PM
Considering a compromise mashaffer Full Range 7 14th May 2006 11:45 PM
OB subs: Best compromise? MtnBob Subwoofers 13 26th May 2004 02:19 PM


New To Site? Need Help?

All times are GMT. The time now is 10:05 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright ©1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2