Power Transformers in Output! - diyAudio
Go Back   Home > Forums > Amplifiers > Tubes / Valves

Tubes / Valves All about our sweet vacuum tubes :) Threads about Musical Instrument Amps of all kinds should be in the Instruments & Amps forum

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 6th May 2006, 06:47 PM   #1
diyAudio Member
 
mod_evil's Avatar
 
Join Date: Dec 2004
Location: Rio
Send a message via MSN to mod_evil
Default Power Transformers in Output!

A friend called me, who is possible use Power Transformers in Output of Tubes.

Fine.

I'm thinking to make a amplifier for mine Sennheiser HD580. With EL84 Pentode in SE.

What they think about this? I have two transformers with 127-220 primaries and 12+12 2A segundaries!

The same friend called me, who I need a LOW voltage ( 6 ~ 7v ) secundaries to can use power transformers in the output.

Can anybody help me?

Thanks in advance,
Felipe Navarro.
  Reply With Quote
Old 6th May 2006, 07:17 PM   #2
Merlinb is offline Merlinb  United Kingdom
diyAudio Member
 
Merlinb's Avatar
 
Join Date: May 2006
Location: Lancashire
I have done this (mine was push pull though). Here's how to choose a transformer:

Decide what primary impedance you want. It might be 5200 ohms for an EL84.

Divide by speaker impedance, it might be 8 ohms.
5200/8 = 650

Find the square root- because you need to find the TURNS ratio from the IMPEDANCE ratio, and one is the square of the other.

sqaure root of 650 = 25
So turns ratio of transformer is 25:1

Divide the primary VOLTAGE of the transformer by the turns ratio. You said you have a 220V transformer, so:

220/25 = 8.8V
So you would need a 220 to 8.8V transformer.

You can work backwards of course too, so:
A 220V : 9V transformer would be close = 4700 ohms primary impedance.
A 220V : 6V transformer would be 10000 ohms primary impedance, also pretty good.
Your 220V : 12V transformer would be 2600 ohms = too low! BUT- connect to a 16 ohm speaker doubles it = 5300 ohm = ok!

However, it will sound BAD for hifi.
Its ok for LoFi, like guitar amps.
For a single ended design, use a transformer capable of twice the wattage than you need, so for an EL84 say a 12VA transformer- nice and big.
  Reply With Quote
Old 6th May 2006, 07:28 PM   #3
diyAudio Member
 
Brian Donaldson's Avatar
 
Join Date: Jan 2003
Location: Texas, Love it or leave it
Your cans have a much higher imp than 8 ohm. I would suggest a OTL cathode follower with a LTP input to preserve absolute phase and give you a few db gain.
  Reply With Quote
Old 6th May 2006, 07:37 PM   #4
Merlinb is offline Merlinb  United Kingdom
diyAudio Member
 
Merlinb's Avatar
 
Join Date: May 2006
Location: Lancashire
There is nothing obviously worng with the circuit, except the standby switch. Disconnecting valve cathodes while HT is applied will damage valves over time. A standby switch should be in the HT supply, before or after the rectifier.

Are you quite sure the oscillation is coming from the output stage? You're not simply hearing oscillation from one of the pre amp stages?

I would perhaps reduce the size of the capacitors C14 and C15 to 33nF to avoid low-frequency oscillation. Also check them for leakage.
  Reply With Quote
Old 6th May 2006, 07:49 PM   #5
diyAudio Member
 
Brian Donaldson's Avatar
 
Join Date: Jan 2003
Location: Texas, Love it or leave it
Oh yea, I also forgot, SE and power trans for OPT is a bad combination. I've heard toroids can make pretty good push-pull opt , but are very intollerant of DC bias, and EI OPT's will have very poor high freq response.

If you parafeed a toriod, you can get decent results, but for HP amp, dump the transformer and use a 10W or so triode cathode follower. Maye a 6SA7?
  Reply With Quote
Old 6th May 2006, 08:29 PM   #6
diyAudio Member
 
mod_evil's Avatar
 
Join Date: Dec 2004
Location: Rio
Send a message via MSN to mod_evil
Hey all,

My Sennheisers has 300ohm impedance.

Merlinb,
If I use a 300ohm impedance, can I use the 12v segundaries???

What transformer i need?

Thanks,
Felipe Navarro.
  Reply With Quote
Old 6th May 2006, 08:54 PM   #7
ilimzn is offline ilimzn  Croatia
diyAudio Member
 
Join Date: Feb 2005
Location: Zagreb
First of all you cannot simply use a power transformer as an output transformer for a SE amp. A SE amp has DC bias current going through the transformer, power transformers are not designed for DC bias (no airgap), hence you can't use them here.
For a PP amp you may be able to use a power transformer as Merlinb suggested. Assuming you can balance the DC currents ideally, a toroidal transformer may provide more than decent results!
The 'use twice the VA rating if it's SE' mentioned by Merlinb is downright WRONG. In PP amps, the size depends on the maximum flux chosen and the lowest frequency you want full power at. For 20 Hz you need a transformer that would have about 6 times higher VA rating if it was used as a power transformer - In THEORY. Various other considerations may require an even bigger core. For SE things are even more complex and because an airgap is needed, the transformer is even larger. 10W SE output transformer cores could easily be used as 100, in some cases even 200VA power transformers if their airgap was removed.
Finally, if you wish to drive 300 ohm headphones with an EL84, you should not need an output transformer at all, if you use the proper topology.
  Reply With Quote
Old 6th May 2006, 10:08 PM   #8
Merlinb is offline Merlinb  United Kingdom
diyAudio Member
 
Merlinb's Avatar
 
Join Date: May 2006
Location: Lancashire
Quote:
Originally posted by ilimzn
[B]First of all you cannot simply use a power transformer as an output transformer for a SE amp. A SE amp has DC bias current going through the transformer, power transformers are not designed for DC bias (no airgap), hence you can't use them here.
You CAN use them, it will simply be EXTREMELY inefficient. I was assuming this was for a small LoFi design or experimentation- for HiFi or prolongued use I'd agree with you obviously. At the end of the day, a transformer is nothing more than some copper around some iron. You can abuse it as much as you want and get it to 'work', but it won't work 'well' granted. It's just a matter of what you want to achieve.
  Reply With Quote
Old 6th May 2006, 10:34 PM   #9
diyAudio Member
 
Brian Donaldson's Avatar
 
Join Date: Jan 2003
Location: Texas, Love it or leave it
When I was about 10, I wrapped about 40 turns of #14 wire around a 1/2"carrage bolt, then another 10 turns of #14 on top of that. I then plugged the first set of windings into the wall outlet. Yes, I was trying to make a transformer. I would say it didn't work, but you may disagree.

With the core saturated, the inductance is greatly deminished and you're heating a tube anode more than anything else. You will get some garbled, highly distorted noise out, but I wouldn't call it working.
  Reply With Quote
Old 6th May 2006, 10:53 PM   #10
RIP
 
pedroskova's Avatar
 
Join Date: Dec 2002
Location: C'ville VA, USA
Use a parafeed topology with power toroids as OPT's , i.e., a choke-loaded tube that is cap coupled to your transformer(no dc to deal with). The smaller power toroids have bandwidths out to 100k.

Search the web for "parafreed" . Plenty of info out there.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Power and Output transformers for sale nafanja Vendor's Bazaar 248 19th October 2011 04:29 PM
GU-50 100W output and power transformers Wavebourn Group Buys 48 15th March 2011 05:34 PM
Power transformers versus amplifier output power..what is your option? destroyer X Solid State 38 9th May 2009 05:23 PM
Help identifying a pair of output transformers and power transformers mjk130 Parts 3 30th January 2009 10:44 AM
Quad II power amps......power output transformers!!! bwes87 Tubes / Valves 3 10th September 2008 02:20 AM


New To Site? Need Help?

All times are GMT. The time now is 11:54 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2