Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Tubes / Valves All about our sweet vacuum tubes :) Threads about Musical Instrument Amps of all kinds should be in the Instruments & Amps forum

DIY tube amp squeals when turned up
DIY tube amp squeals when turned up
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 2nd September 2005, 12:14 AM   #1
jjai is offline jjai  United States
diyAudio Member
Join Date: Mar 2005
Location: San Francisco, CA
Default DIY tube amp squeals when turned up

I just built a Real McTube preamp for my guitar:

and it worked great! It's my first tube project (I'm a real tube newbie), so I'm very happy.

Never able to leave good enough alone though, I decided to modify it, substituting components based on a Tweed Fender Princeton 5F2A schematic:

My changes can be summarized as follows:
- replaced C5 (input coupling cap) with 68k grid resistor
- replaced R5 and C7 (1st stage cathode resistor/bypass cap) with a 1k5 resistor and 22uf cap
- replaced R7 and C8 (2nd stage cathode resistor/bypass cap) with a 1k5 resistor
- replaced R4 and R6 (1st and 2nd stage plate resistors) with 120k resistors (ran out of 100k's)
- replaced RV1 (gain control) with the Princeton's gain/tone stack (2 1M pots, and 2 caps)

Everything else remains the same - the only other difference is that I'm running it with 300ma transformers, so I get about 110V at the plates (vs. the 140 of the original McTube design, or 150 of the original Princeton).

Everything sounds great until I turn the gain and/or the tone control past 9 -- then it starts squealing! With the gain up to about 8.5, it sounds clean and sparkly, between 8.5-9, it starts to get a dirty, and at 9, it immediately (and very abruptly) gets really distorted and starts squealing uncontrollably.

I did some research and came up with the following theories:
- grid resistor isn't close enough to the tube socket?
- plate resistor value is off? (try 100k's)
- not enough voltage - use larger transformers or modify component values (need larger plate resistors?)

Any ideas on what might be wrong, or suggestions on tests I could try?

  Reply With Quote
Old 2nd September 2005, 12:40 AM   #2
gingertube is offline gingertube  Australia
diyAudio Member
Join Date: Oct 2004
Location: Adelaide South Oz
Neither circuit shows grid stopper resistors on the grid of the 12AX7 connected to the wiper of the gain control. The thing is therefore most likely oscillating. Add a resistor in between the wiper and 12AX7 grid.
This resistor will work with the Miller capacitance of the 12AX7 input to form a low pass filter which will cure the oscillation. You can also trim the resistor value to get the sonics (high frequency response you want). Try 47K and adjust down (say 22K or 10K) f not enough highs, adjust up (say 100K) if its too bright. The body of the resistor wants to be directly on the grid pin of the tube socket, i.e. the resistor lead on that side to be VERY short. Make sure that you have that 68K resistor as a grid stopper on the input 12AX7 stage too. Again body of resistor as close to the grid pin as possible.
  Reply With Quote
Old 3rd September 2005, 01:33 AM   #3
Sch3mat1c is offline Sch3mat1c  United States
diyAudio Member
Sch3mat1c's Avatar
Join Date: Jan 2003
Location: Milwaukee, WI
Send a message via ICQ to Sch3mat1c Send a message via AIM to Sch3mat1c
"no grid stoppers"

"therefore it's oscillating"

Gee, shoulda told that to all the RF engineers of yore. Coulda saved a lot of time

I'm betting you have too many capacitors in the circuit and too much gain. That's a good way to make a phase shift oscillator. The final cap of course probably *wasn't* intentional, but the gain allows it. Try seperating input and output leads, shielding them if necessary.

Seven Transistor Labs, LLC
Projects and Resources / Electronic Design and Consultation
  Reply With Quote
Old 6th September 2005, 11:07 PM   #4
jjai is offline jjai  United States
diyAudio Member
Join Date: Mar 2005
Location: San Francisco, CA
FYI, in case anyone is interested, I wanted to close the thread on this topic:

I added a 22k grid stopper on the second stage (directly on the tube socket), and this stopped most of the squealing (still had some when the volume was at 100%). After moving the grid stopper on the first stage to the tube socket, all of the squeal disappeared.

It might be psychological, but i think I did lose a little high end after adding the grid stopper on the second stage. Still sounds plenty good and bright, but I might try switching to a 10k resistor some time.

I'm interested in squeezing out a little more gain, if it's possible without affecting tone -- maybe the simplest is to switch from the 12AT7 I'm currently using to a 12AX7? If anyone has suggestions, I'd love to hear them.

Thanks again for your help -- you helped me solve the problem, and learn about the weird and mysterious world of theremonic emission!
  Reply With Quote
Old 7th September 2005, 01:32 AM   #5
Trout is offline Trout  United States
diyAudio Member
Trout's Avatar
Join Date: Nov 2004
Location: Midwest Madman
I Built a McTube last fall as a warm up project. I nicknamed it SQUEAKY as it was a squealing monster. I had it feeding a 6AQ5 SE amp that I had scratch built. Interestingly, I did the same grid stopper fix, Made it better but not perfect. When I ran the 12AX7 in the unit it was vicious distortion wise, I followed Fred's advice and altered the caps:
. Remove C7 - you'll have less gain, but see how much cleaner the tube sounds? Short the cathode directly to ground - see how much dirtier the sound gets as the grid is driven into conduction?
I reduced the Cap in first stage to (C7) 25UF, (C8) to 50UF
I Also changed C5 & C6 to .1uf. RV1 to 1 meg pot

I was able to run the 12AX7 without excessive squealing but it was still very close to the edge.

Paul Marossy Had a pretty nice construction article with mods on this unit at his Site
DIY Guitar In The DIY Effects section.
Sadly he reports that Fred Nachbaur, has recently passed away.

Good Luck!
  Reply With Quote


DIY tube amp squeals when turned upHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
hum on pre-amp when volume is turned up phrarod Tubes / Valves 6 14th June 2009 06:11 PM
cracked el34 -> replacement squeals PM650 Tubes / Valves 1 19th May 2008 02:47 PM
Pop when amp is turned off boostin1989 Solid State 6 10th October 2006 04:10 PM
Leach amp has hum only when turned off! kiwi_abroad Solid State 12 26th March 2004 03:17 PM
Hum when volume is turned down miguel2 Tubes / Valves 34 18th March 2003 06:51 PM

New To Site? Need Help?

All times are GMT. The time now is 04:07 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio