Help Needed: Lower Gain on a Tube Amp? - diyAudio
Go Back   Home > Forums > Amplifiers > Tubes / Valves

Tubes / Valves All about our sweet vacuum tubes :) Threads about Musical Instrument Amps of all kinds should be in the Instruments & Amps forum

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 23rd February 2013, 04:31 AM   #1
twix* is offline twix*  Canada
diyAudio Member
 
Join Date: Jan 2005
Location: Regina, Sask.
Default Help Needed: Lower Gain on a Tube Amp?

Hi everyone, Can someone with some Smarts please help me figure out how, if possible to lower the gain on a very simple tube headphone amplifier circuit. I have very limited(basically zero) knowledge when it comes to eletronics and circuits on how they work etc. All I am good at is following instructions with great soldering skills.
The amplifier is a old Antique Sound Lab MG-HEAD OTL Headphone amp that I woke up from the dead. It was collecting dust for many years and now I want to try use it again. Back in the day, I did mod the crap out of if. It still works great except it would be real nice if I can lower the gain somehow because as of right now, when I turn volume very slight it gets too loud to quick. It always had this issue. The only way I knew years ago to change gain was to install a lower gain tube which works but is limited. I am sure (hope) that it is as simple as changing a ground resistor value, but which one? Please help.
Here is schematics. This is a DT version and mine is OLT version . Exact same circuit but not shown is the added OTL output added which should not matter to change gain.

mg head otl - Google Search
  Reply With Quote
Old 23rd February 2013, 06:15 AM   #2
diyAudio Member
 
azazello's Avatar
 
Join Date: Aug 2008
Location: Bulgaria
To change input tube, it's need more skill how the tube works.
Simple is to put R divider on the input: Connect serial two resistor /for ex./ 220 kohm each. One end connect to middle point of potentiometer, second end - to ground and middle point of 220 & 220 kohm - to grid of input tube.
  Reply With Quote
Old 23rd February 2013, 06:24 AM   #3
diyAudio Member
 
Join Date: Apr 2004
Location: Monroe Township, NJ
Install 100 KOhm 1% tolerance resistors in the lines between the I/P jacks and the "tops" of the volume controls. The additional resistance attenuates the I/P signal by 6 dB. No more "hair trigger" volume control!

While the unit is on the bench, consider replacing D1 through D5 with UF4007s. The OEM parts generate a good deal of switching noise. UFnnnn parts are drop in replacements for the corresponding 1Nnnnn parts that generate much less switching noise.
__________________
Eli D.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
How to lower the gain of this headphone amp eimis Solid State 18 21st June 2012 04:09 PM
Tube Amp Gain V.S. RF Gain Einric Tubes / Valves 10 21st May 2012 09:36 PM
Lower gain 12AX7? PeteMcK Tubes / Valves 43 12th February 2011 04:49 PM
help me lower the gain of this preamp pls milen007 Tubes / Valves 2 23rd January 2009 01:25 AM
Lower the gain on a Pass X250.5? aljordan Pass Labs 10 8th January 2009 08:26 PM


New To Site? Need Help?

All times are GMT. The time now is 04:47 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2