Go Back   Home > Forums > Amplifiers > Tubes / Valves

Tubes / Valves All about our sweet vacuum tubes :) Threads about Musical Instrument Amps of all kinds should be in the Instruments & Amps forum

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 23rd February 2013, 12:08 AM   #1
HP8903B is offline HP8903B  United States
diyAudio Member
 
Join Date: Jun 2010
Default Help: Hickok Western Electric KS-15750 Calibration

I am trying to calibrate a Hickok KS-15750.

I attached the calibration procedures.

Could someone clarifies section 5. Micromhos step "d" and "e" ?

After step "c", I went to step "g" and the readings are correct except "Low 6000" and "Low 600"

Also, the location of R15 - R18, R28, R29, and R42. Particularly R15 and R42 ?
Attached Files
File Type: pdf Hickok KS-15750-L1 Manual.pdf (832.9 KB, 14 views)
  Reply With Quote
Old 23rd February 2013, 07:33 PM   #2
diyAudio Member
 
drossetti's Avatar
 
Join Date: Dec 2011
Location: Annapolis, Maryland, USA
The "shunt pot" referenced in 5d is the one controlled by the Shunt dial. It is a special dual resistor (R4-R5) pot made by Mallory, identified by Item No. 26 on your parts list. When Hickok initially installed this part, the individual pot cases (front and rear) were free to turn independently. Following the attached calibration procedure, the Hickok production team would: ensure the function switch was set to "3000 High", set the Shunt dial on 73, press the locking P4 button to set the tester to the Dynamic Transconductance test function, and then would rotate the rear section of the pot until the main meter read 1000. This properly calibrates the two circuits on either side of the 150 ohm sections of the pot. Checking to be sure the Shunt dial is still set on 73, and the main meter is still reading 1000, they would lock the rear section of the shunt pot to the front section by placing a dab of solder on the seam between the two pot halves (5e). If you find that as you follow this procedure, set the Shunt dial to 73, punch in P4, and your main meter reads 1000 (plus or minus two divisions, or in other words, between 900 and 1100) you should be good to go. If not, you are going to have to get out the soldering iron and the solder sucker to free the rear half of the pot and re-calibrate it. Does that clear things up?
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Hickok calibration famousmockingbird Tubes / Valves 5 8th February 2013 02:09 PM
Help with Calibration: Hickok Western Electric KS-15750-L1 Tubes Tester HP8903B Tubes / Valves 17 21st December 2012 07:14 AM
Help: Hickok Western Electric KS-15750-L1 Tubes Tester Maintenance and Calibration HP8903B Tubes / Valves 9 20th October 2012 05:57 PM
Western Electric settings for Hickok 600A? ethanbriz Tubes / Valves 3 19th July 2010 12:42 AM
Look for Western Electric KS-16547-L1 circuit diagram RCA245 Tubes / Valves 0 29th May 2006 07:52 PM


New To Site? Need Help?

All times are GMT. The time now is 08:35 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2