Aikido 9-pin all-in-1 headphone amp problem - diyAudio
Go Back   Home > Forums > Amplifiers > Tubes / Valves

Tubes / Valves All about our sweet vacuum tubes :) Threads about Musical Instrument Amps of all kinds should be in the Instruments & Amps forum

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 15th February 2013, 01:37 AM   #1
jilldwr is offline jilldwr  Canada
diyAudio Member
 
Join Date: Mar 2005
Location: Midland Ontario
Default Aikido 9-pin all-in-1 headphone amp problem

I've just finished building my aikido HP amp using 6CG7's as input tubes and
6DJ8's as output. For the last couple of nights I've been burning in the amp and testing with my 3 sets of headphones. I've got an AKG K240 @ 600ohms, Beyer DT880 @ 600ohms, and modded Fostex T50RP at 50ohms. What I've noticed is the Fostex sound completely sucked out with this amp, very muddy bass and an almost echo-ish sound. The two 600ohm cans sound superb. I know it's not the Fostex cans as I use them daily at work with a Shiit Asgard amp and brought them home just to try with this Aikido.

When building, I chose resistor values for using 32ohm cans optimally, so the 600 ohm cans should be the ones to sound deficient. I wired a 330uf electrolytic parrallel to the other two output caps which is switched into the circuit when using the 50 ohm load. The only departure from Johns design I've made is to leave the 30uf Daytons in the circuit when I switch in the 330uf caps.

Has anyone else had issues with low impedence cans and this amp? Do you think this amp just doesn't like Planar Magnetic headphones? Would it make that much difference if I switch the 30uf Daytons out of the circuit when switching the 330uf electrolytics in, or just leave them in?

I'm thinking dampening factor may be the culprit, if so, what could I do to fix this, output trannys?

I've attached the schematic I built to showing options based on impedence and my choices.
Thanks,
D.W.
Attached Images
File Type: jpg Rev-A Schematic.jpg (249.6 KB, 171 views)
  Reply With Quote
Old 6th August 2013, 04:35 AM   #2
halitun is offline halitun  United States
diyAudio Member
 
Join Date: May 2007
Location: New Jersey
Hello there. I built the headphone amp using the 6cg7 inputs and 6h30 outputs based on this link from John Aikido 9-pin Low-Impedance Headphone Amplifier . It seems to be the same as your thumbnail schematic but with the 6h30 setup. I find that my 600 ohm Beyerdynamics work great with virtually no hum while any low impedance phones exhibit hum. So yes, I'm experiencing the same problem. No ready solution for you except to just to listen with the 600 ohm phones or perhaps bring down your Ik a bit so that you can increase R12 to reduce ripple.

Last edited by halitun; 6th August 2013 at 04:40 AM.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
GlassWare Audio Aikido Rev C 9-pin board - stuffed & tested with 6GU7s beeah Swap Meet 7 15th September 2009 06:27 PM
4 Pin Amp output to 3 Pin headphone jack? StrayS2k Headphone Systems 3 17th February 2009 05:46 PM
Use 9 pin Aikido PCB kit or buy 8 pin ? Renron Tubes / Valves 6 25th November 2007 05:52 PM
Aikido Headphone Amp lordearl Headphone Systems 2 14th June 2007 03:19 PM
my aikido headphone amp - almost there jarthel Headphone Systems 5 27th April 2007 02:07 PM


New To Site? Need Help?

All times are GMT. The time now is 08:32 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2