Grommes/PE S-35 questions Grommes/PE S-35 questions - diyAudio
Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Tubes / Valves All about our sweet vacuum tubes :) Threads about Musical Instrument Amps of all kinds should be in the Instruments & Amps forum

Grommes/PE S-35 questions
Grommes/PE S-35 questions
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 15th September 2012, 06:16 PM   #1
Dill Pickle is offline Dill Pickle  United States
diyAudio Member
Join Date: Aug 2012
Default Grommes/PE S-35 questions

I'm new to tube amps, but have a pretty good understanding of physics and electronics. I've been reading quite a bit to get a handle on the basics, but it's sometimes better to throw a question to the maestros! I picked up an on Grommes/PE s-35 PA amp at a garage sale. It seems to be pretty well known model, at least there is some info online, and schematic. I made the mistake of turning it on without using variable voltage. All the tubes glowed and I had a speaker hooked up so it would have a load, but no sound at all comes out. I modified a guitar cable to have RCA jack to use the AUX input because the mic inputs are an old coaxial type( Im going to solder a 1/4" jack, but first just wanted to see if it works). After letting it warm up for a while, everything seems fine, no excessive heat or smells, tubes glowing etc. but the "neon power indicator" as its called in the schem. doesn't come on. There is a bulb that lights up the logo that works, and the power ind. did come on for a bit when I turned it off. What ive concluded is there IS power getting to the tubes, but no sound at all, so maybe a tube is bad? Or maybe the power transformer?
Thanks for any input you all might have...
  Reply With Quote
Old 16th September 2012, 05:12 PM   #2
Palustris is offline Palustris  United States
diyAudio Member
Palustris's Avatar
Join Date: Aug 2006
Location: Cape Cod
Start by measuring the voltages and comparing to the schematic. Make sure all the heater currents are correct; then follow the B+ to make sure they are correct. Measure the voltages on the output tubes and ensure they are correct; there should be -27V on the output tube grids. Make sure this is the case or the coupling caps to the output tubes will need to be replaced or the bias supply is not working. Basically, you need to go through the amp with your volt meter to ensure all the voltages are correct. If they are not correct you need to find the reason why.
  Reply With Quote
Old 18th September 2012, 08:28 PM   #3
Dill Pickle is offline Dill Pickle  United States
diyAudio Member
Join Date: Aug 2012
Thanks for the response! With the help of a tinkering friend, found that one of the pre-amp tubes, two 6eu7s, was shorting out. I swapped them with a few that came with the amp at the garage sale, and it came to life! It sounds great as is, but ill probably do a few mods, maybe rewire the preamp sockets to take 12ax7s, as ive heard they are pretty close to 6eu7s. Thanks again!
  Reply With Quote


Grommes/PE S-35 questionsHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Grommes 260A DIY report, questions, suggestions Jap Tubes / Valves 7 20th November 2011 06:04 PM
ST-35 Build Using PC13 Boards Questions and Thoughts atwageman Tubes / Valves 3 12th November 2009 06:50 PM
General questions before finishing up ST-35 clone ThSpeakerDude88 Tubes / Valves 8 18th September 2007 12:32 AM
A few PE Dayton 3-way crossover questions... ptwining Multi-Way 2 9th July 2006 12:50 AM

New To Site? Need Help?

All times are GMT. The time now is 04:52 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio