diyAudio

diyAudio (http://www.diyaudio.com/forums/)
-   Tubes / Valves (http://www.diyaudio.com/forums/tubes-valves/)
-   -   Looking for goodme proven 2A3 SE project (http://www.diyaudio.com/forums/tubes-valves/186710-looking-goodme-proven-2a3-se-project.html)

slav 9th April 2011 09:22 AM

Looking for goodme proven 2A3 SE project
 
Hi to All
As in the title I am looking for well designed 2A3 SE project , 8-10W under 8ohm load , so far I found Andrea Ciuffoli's PSE amp ( I wonder if anyone built that one ?).

Evenharmonics 9th April 2011 03:46 PM

Quote:

Originally Posted by slav (Post 2532755)
8-10W under 8ohm load

You want 300B for such output, not 2A3.
TubelabSE Manual
JE Labs 300B SE Amp

boywonder 9th April 2011 06:21 PM

Furthering what Evenharmonics mentioned above, if you are married to the 2A3, the 2A3 will also pop right into the TubelabSE but you will end up with something less than 8W (around 3-4W). You need different B+ voltage, Filament voltage, and maybe a different output transformer primary impedance.

Tubes and Transformers

slav 9th April 2011 08:00 PM

I was thinkig about parallel SE , which gives something about 8W ,but it's quite expensive (four matched2A3 woul cost a fortune) , so 3000B SE it is .Which design would be the best and what suitable speakers to match it?Curently I'm using ProAc Tablette 2000 (87-88dB) wit El34 PP , listening to all kind of music from jazz to The Cure , Depeche Mode ,Prince ,classical etc

costis_n 9th April 2011 08:14 PM

Quote:

Originally Posted by slav (Post 2533229)
I was thinkig about parallel SE , which gives something about 8W ,but it's quite expensive (four matched2A3 woul cost a fortune) , so 3000B SE it is .Which design would be the best and what suitable speakers to match it?Curently I'm using ProAc Tablette 2000 (87-88dB) wit El34 PP , listening to all kind of music from jazz to The Cure , Depeche Mode ,Prince ,classical etc

With this kind of speaker sensitivity (which also implies a complex crossover) , the best design would be a El34 PP :D

slav 9th April 2011 08:23 PM

As I said I will be looking for new speakers

euro21 9th April 2011 09:09 PM

300B SE, Powerdrive
 
D3a (cascode CCS anode load) with Powerdrive source follower, 300B SE (380-400V, 70mA)
6W A1 mode, up to 10-11W A2 mode.

Evenharmonics 9th April 2011 11:27 PM

Quote:

Originally Posted by slav (Post 2533245)
As I said I will be looking for new speakers

These speakers are made for low power SET amps.

tinitus 9th April 2011 11:32 PM

any SE amps with 3x 6V6 in paralel ?

slav 9th April 2011 11:35 PM

Hi
What about 300B in parallel , it should give reasonable power to source any speakers ?


All times are GMT. The time now is 04:52 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio


Content Relevant URLs by vBSEO 3.3.2