diyAudio

diyAudio (http://www.diyaudio.com/forums/)
-   Tubes / Valves (http://www.diyaudio.com/forums/tubes-valves/)
-   -   Troubleshoot help for vibrato type problem (http://www.diyaudio.com/forums/tubes-valves/181266-troubleshoot-help-vibrato-type-problem.html)

PHOENIXJAZZ 16th January 2011 04:57 PM

Troubleshoot help for vibrato type problem
 
2 Attachment(s)
Hi,
I've rebuilt an old Bogen CHB10a and it works fine with one problem!
Sound is nice, just what I want/expect but when I turn the volume up past about 8 or so I get a vibrato type sound out of it.
I have not run into this before and I am hoping someone with more experience might know where to look.
I've attached the Schematic and a very small mp3 (zipped) file so you can hear what's going on.
I replaced all components with new or NOS for some of the foil caps. Everything was on value when I put it in.

Thanks in advance for any help or suggestions.
Chris

Brion55 16th January 2011 05:03 PM

Possible power supply decoupling problem?

M Gregg 16th January 2011 05:29 PM

Hi,

A few ideas.

Check value of B+ rail when Warble happens does it "dip".

What is S2? Does the problem change if switch positions are changed?

Also what happens if tone control is changed?
Check is C7 cap faulty?

Can you post PSU schematic?


Regards
M. Gregg

dcgillespie 16th January 2011 06:13 PM

Since the schematic says it's modified, it makes it harder to know where to start -- but it sounds like a classic case of inadequate decoupling in the power supply, so that feedback occurs back to an earlier stage when the gain is advanced beyond a certain point. I would use two separate isolated B+ points for the first two stages to confirm if this is what's happening.

Dave

Wavebourn 16th January 2011 06:32 PM

It looks like feedback through power supply, but may be HF oscillation of the 1'st stage as well. Try 68K grid leak resistor.
Add PS filter capacitance in parallel to existing one and check if frequency of vibrato goes lower, or if it stops.

PHOENIXJAZZ 17th January 2011 03:45 PM

Thanks All.
I'll take a look in the places you suggest and let you know how it turns out.

PHOENIXJAZZ 25th January 2011 04:40 PM

Thanks for the help folks,
Replacing the PS filter Caps one at a time fixed most of the problem. Adding the 68k Grid Leak resistor cleaned up the rest but did make it more sensitive to picking up radio signals!
Looks like I have more reading to do.........

Thanks again.

Chris

Wavebourn 25th January 2011 05:21 PM

Quote:

Originally Posted by PHOENIXJAZZ (Post 2445844)
Adding the 68k Grid Leak resistor cleaned up the rest but did make it more sensitive to picking up radio signals!

That means, your input stage must be shielded.

Try to cover it by grounded foil to check if it helps, then construct a shield made from thin copper, or even from tuna can metal if you can't find copper.

trobbins 25th January 2011 10:38 PM

You're running grid leak bias on first stage. That may be quite temperamental. I suggest temporarily changing to a standard cathode bias configuration (eg. 1.5k or 2k2 bypassed with 25uF 16V) to see if that is the major influence.

Also use say a 68k grid stopper placed on the input valve base. You may also need to use a shorting input jack if you don't have a low impedance pickup connected, or a phono output stage connected.

As per post above, insert an RC decoupling of the power supply rail from PI stage to input stage.

Ciao, Tim

Wavebourn 25th January 2011 10:59 PM

My bad; I meant grid stopper 68K, not a grid leak resistor.


All times are GMT. The time now is 03:06 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio


Content Relevant URLs by vBSEO 3.3.2