diyAudio

diyAudio (http://www.diyaudio.com/forums/)
-   Tubes / Valves (http://www.diyaudio.com/forums/tubes-valves/)
-   -   Peavey Valveking 100- static sound during warm-up (http://www.diyaudio.com/forums/tubes-valves/175077-peavey-valveking-100-static-sound-during-warm-up.html)

Rotus623 9th October 2010 02:25 PM

Peavey Valveking 100- static sound during warm-up
 
I checked all of my speaker wiring,and no problems. For some reason, when I fire up the amplifier, as it warms up I hear static like there is a loose wire connection and someone is wiggling it around. When the amp is warmed up, it doesnt make any of those sounds. Does anyone know what components that I should check first?

Gilgy 9th October 2010 04:21 PM

Are you letting the tubes heat up? Sounds like you're switching it "full on" from cold when you get the static sound. Turn it on standby first, leave it one minute for the tubes to heat up, then take it off standby.

DF96 9th October 2010 05:34 PM

Is the sound coming from the speaker or the amp itself? If the latter, then it is probably just the valves warming up. Nothing to worry about. Don't worry about the 'standby' switch - it's probably only there because musicians expect to see it.

Rotus623 9th October 2010 10:22 PM

Gilgy, this happens when I do not allow for the amp to warm up, I am not playing the guitar, but the standby switch is on. Thanks for the pointer. DF96, the sound is coming from the speaker. The amp just makes a sound like a valve is turning on.

Thanks guys!!

richwalters 10th October 2010 11:26 AM

I suspect a valve is on it's way out and may be oscillating in the warm up phase. Try tapping them in turn and noticing any changes. Replacement is the only cure.

richy

DF96 10th October 2010 01:52 PM

Could be a valve with a dodgy weld, or resistor/capacitor failing. It will probably get worse before it fails altogether. As well as tapping the valves you could try gently tapping other components (with an insulator, of course!). You might at least narrow it down to a particular stage.

Rotus623 10th October 2010 03:20 PM

Right. Well I guess Ill try tapping the tubes first, and then if I dont hear any strange noises, Ill take the chassis out of the cabinet and give it an inspection.

Rotus623 12th October 2010 11:27 PM

So guys, I tapped all of the tube and none of them are microphonic. I was jamming today at 3 or 4 and the gain started fading out. I kicked it over to clean channel, and the volume was significantly lower than it was when I started playing. This was in a period of about 10 minutes. Does anyone have any that would lead me to pre or power amp tubes? Id like to narrow it down to tubes before I drop 1XX dollars into tubes.

Rotus623 13th October 2010 12:30 AM

So check these out guys, upon further inspection this is what I saw. Is this what it looks like when the vacuum seal has a leak?
http://i803.photobucket.com/albums/y...o/PA120038.jpg
http://i803.photobucket.com/albums/y...o/PA120037.jpg

Rotus623 7th November 2010 06:26 PM

Okay, well I changed all of the tubes out and now I still have a static noise during the warm up phase. Except now it takes a lot longer to go away. Any suggestions why the amp is making a static noise when the volume is turned all the way down? When it is in standby mode it is totally quiet.


All times are GMT. The time now is 03:19 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio


Content Relevant URLs by vBSEO 3.3.2