Go Back   Home > Forums > Amplifiers > Tubes / Valves

Tubes / Valves All about our sweet vacuum tubes :) Threads about Musical Instrument Amps of all kinds should be in the Instruments & Amps forum

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 13th September 2010, 08:22 AM   #1
diyAudio Member
 
Join Date: Nov 2009
Default reverb

hi to all
i want to add a reverbtank in a home made guitar amp
i have a spair se 2.5k to 8 ohm and 600 ohm transformer
also a pp 10K to 2.5 _ 4 ohm
can someone advice a schematic to use one off these transformers
or even shematics without transformers to add a reverb tank
i have some el84 , ef86 , and ecc 8XX tubes laying around
thanks in advance
Marc
  Reply With Quote
Old 13th September 2010, 09:36 AM   #2
diyAudio Member
 
Join Date: Jan 2002
Location: nowhere
check schematicheaven.com

In addition to the various amps with built in reverb, I think there are a couple of stand alone units.
  Reply With Quote
Old 13th September 2010, 07:06 PM   #3
45 is offline 45  Italy
diyAudio Member
 
45's Avatar
 
Join Date: Dec 2008
Location: United Kingdom
Use an ECC81 with the two plates in parallel. 5-6 mA for each unit DC current (data sheet operative points are a good start). 10K is fine for this. The secondary of the transformer has to match the impedance of the tank.
Then you need another preamp that could be half of ECC83 or a op-amp.
Actually an op-amp used as a current amplifier will work fine. In fact the spring is basically a coil with its own inductance and the higher the frequency the higher current to drive it. What you don't want is reverb at low frequencies but this is easier to manage, both with the transformer and the coupling caps.

Cheers,
45
  Reply With Quote
Old 13th September 2010, 08:52 PM   #4
Trout is offline Trout  United States
diyAudio Member
 
Trout's Avatar
 
Join Date: Nov 2004
Location: Midwest Madman
I would really like to find/see a simple way to put a Belton digi-log into an amp.

I always find one of my amps a bit on the dry side and would think that unit is compact enough to easily fit provided the support circuitry is not excessive.
Space is at a premium and to much extra stuff would be a factor
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
problem with old reverb - help? 2SK30 Digital Source 5 22nd July 2008 10:56 AM
convolution reverb eStatic Everything Else 0 19th March 2008 03:21 PM
tube reverb audiofun Instruments and Amps 11 7th May 2007 03:19 AM
Digital reverb help spirod Digital Source 0 11th October 2006 06:12 AM
Digital Reverb ! -_nando-_ Digital Source 5 11th April 2006 05:29 PM


New To Site? Need Help?

All times are GMT. The time now is 08:07 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2