Help needed with my Epi Valve Jr - diyAudio
Go Back   Home > Forums > Amplifiers > Tubes / Valves

Tubes / Valves All about our sweet vacuum tubes :) Threads about Musical Instrument Amps of all kinds should be in the Instruments & Amps forum

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 30th December 2009, 09:39 AM   #1
diyAudio Member
 
Join Date: Dec 2009
Default Help needed with my Epi Valve Jr

I know this is not a guitar amp forum, but all you knowledgable and experienced DIY'ers are bound to be able to answer some questions I have ...

I have a sweet little valve amp (5W provided by a 12AX7 and an EL84) from Epiphone. It's their Vavle Junior head.

I've been modding it to get better tones. All mods so far came from a book, and presented no problem at all. (including adding a Negative Feedback Switch) to allow switching between default (pin 8 of 12AX7 goes to ground via a resistor (R9) and via an electrolytic cap (C3)) and NFB mode : pin 8 goes to ground via 1.5K resistor (R9) and goes, via NFB switch, to a 47K resistor and then straight to the output jack's pin.

Worked fine.

A mod not described was adding a tone stack. I found a sweet little tonestack (body and presence) from www.muzique.com. I wanted to be able to have or the raw amp sound, or the sound through the tone stack. So I cut a trace running from the wiper of the volume pot meter (1M) to pin 7 on the 12AX7. I wired in a 2pdt switch, of which one end uses a jumper to implement a bypass. This is my raw amp sound position. (without the tonestack that I still need to build).

I was stupid enough to swap out the standard 1M clearly oxidized volume pot meter for a new one at the same time ... 2 changes at once = dumb dumb dumb

Switchin the amp on, I seem to hear more hum/noise on the signal. In bypass (the new 2pdt) there is guitar sound...but if I flip the NFB switch, it totally breaks up a squeels... this never happened before!

Also, if I measure the voltage at pin 7 of the EL84, I get a reading that depends on the (variable) resistance of the new pot meter I put in... I'm quite sure that this voltage was a constant 305V before .... I've measured it multiple times before, and regardless of pot meter, it was always 305V ... now it seems to fluctuate .... I've had readings of 160V, 200V, 305V (when I open the volume pot completely)

I used 26 gauge wires for the wiring of the switches and the new pot meter. I read somewhere of this guy who describes some similar symptoms...in his case, it seems to have been fixed by using shielded wire instead of normal wire....

Is there someone who can explain this to me? How can using normal wire instead of shielded wire have such an effect on the amp? Is 26 gauge (which I use for effect pedal running at a mere 9V) even usable for amps? I can dig that shielded wire can have an effect on the noise on a signal, but how about the voltage readings on EL84???

The schematics for the Epi Valve Jr can be found at page 3 here:
http://www.blueguitar.org/new/schem/...hemia_mods.pdf

Mind you, mine is a bit different (new version) with improvements in caps and resistors (e.g. R9 is at 1.5K, and I swapped out C3 for a 1uF).

I really hope one of you more experienced DIYers can at least give me some clues/explanation ... I'm fairly new at this
  Reply With Quote
Old 30th December 2009, 11:04 PM   #2
Cassiel is offline Cassiel  Libya
diyAudio Member
 
Cassiel's Avatar
 
Join Date: Sep 2004
Location: Madrid
The circuit is prone to oscillation. A change in the layout is giving you problems. You have paid the price for messing around...if you can't fix it leave it as it was.

Quote:
but if I flip the NFB switch, it totally breaks up a squeels... this never happened before!
Reverse the transformer secondary leads.
__________________
Effeminate Audio
  Reply With Quote
Old 31st December 2009, 04:02 AM   #3
diyAudio Member
 
Join Date: Dec 2009
I've taken out completely the original volume pot including the PCB mounted connector, resoldered a pot using shielded wire. Since I cut the signal trace, I soldered the signal lead directly on pin 7 of the 12AX7. Works like a charm again.

I think it was a combination of oscillation and a bad solder joint ... the two extra solder point I created don't have that much copper around them and were hard to solder...

Thanks for the input, I'm going to dig a little deeper into "oscillation" since I don't know too much about that.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Swap Shanling CD-T80 valve CD player for Quad valve equiment johnm Swap Meet 2 24th September 2009 12:15 PM
FS: Four EPI 8" Woofers - 2ohm model - $50 obo for all walker112 Swap Meet 0 4th February 2009 04:43 PM
EPI 110C speakerset MadsKaizer Multi-Way 14 27th November 2008 03:34 PM
Horn Sub Jr. Tomac Subwoofers 2 2nd October 2008 05:29 AM
testing of EPI woofers jmikes Multi-Way 0 17th November 2004 03:36 PM


New To Site? Need Help?

All times are GMT. The time now is 09:59 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2