
Home  Forums  Rules  Articles  diyAudio Store  Blogs  Gallery  Wiki  Register  Donations  FAQ  Calendar  Search  Today's Posts  Mark Forums Read  Search 
Tubes / Valves All about our sweet vacuum tubes :) Threads about Musical Instrument Amps of all kinds should be in the Instruments & Amps forum 

Please consider donating to help us continue to serve you.
Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving 

Thread Tools  Search this Thread 
28th January 2003, 09:32 PM  #1  
diyAudio Member
Join Date: Oct 2002
Location: Brooklyn, NY

Slew Rate Limiting... continued.
I took the liberty of starting a new thread on this interesting subject. I apologize to Dmitry for cluttering his other thread.
Anyway, this was the last relevant post: Quote:


29th January 2003, 03:15 AM  #2 
diyAudio Member
Join Date: Oct 2002
Location: Brooklyn, NY

Here are the numbers.
Ok, let's use the 2A3 from the other thread.
Cinput=Cgp*(VG+1)+Cgk+Cpk*(VG+1) So, the input capacitance of a 2A3 is 121.9pF 2piFVp/1,000,000=V/mS F=20kHz, Vpkpk=90V Required slew rate=11.31V/mS I=C*Sr .0001219*11.31=1.38mA So to wrap up, only 1.38mA is required to "drive" the input capacitance of a 2A3. Not very much! And this is at the limit of digital frequency response, and with a FULL amplitude signal input of 90 volts peaktopeak. And to finish my example from before, with the 71A, the calculated input capacitance is actually just half what I guessed at. It's really 41.7pF So.... to drive a 71A you need only 0.42mA of current. Joel 
29th January 2003, 08:47 AM  #3 
diyAudio Member
Join Date: Nov 2002
Location: North Herts, UK

...work is a pain...
Hi Joel,
Sorry not to reply. Got a big problem at work to solve before I can write one out. Briefly the input capacitance calculation is incorrect. Cin=Cgk+Cgp(1+mu) gets you the real world figure... more later ciao James 
29th January 2003, 12:00 PM  #4 
diyAudio Moderator Emeritus
Join Date: Jan 2003
Location: Near London. UK

Slew rates, opamps, and glass
At the risk of muddying the waters, slew rate specifications are great for opamps, but not quite so useful for valves. Try this approach, and I think you will see what I mean...
Find the input capacitance of the load. Determine its reactance at the highest frequency of interest. Use Ohm's law to calculate the peak current at that frequency. Now, go back to the original loadline of the driver stage, and plot that peak current directly above and below the operating point (the phase lag of the capacitance causes it to draw maximum current at zero voltage swing). Plot the maximum voltage swing (positive and negative) on the loadline. Finally, draw an ellipse through all four points. This is your AC loadline. When I have done this, I invariably feel that I would like a lot more current through my driver to keep the distortion down (even if it is ultrasonic).
__________________
The loudspeaker: The only commercial HiFi item where a disproportionate part of the budget isn't spent on the box. And the one where it would make a difference... 
29th January 2003, 01:34 PM  #5 
diyAudio Member
Join Date: Nov 2002
Location: North Herts, UK

...Slew rate current...
First a confession  some of my quoted numbers were wrong due to my sloppy use of Jim de Korts spreadsheet  Sorry .
To check I'm doing it right I have derived the equation for input current required for zero slew rate limiting into a valve and my work is included below for all to mock I will rework my figures and ajust my conclusions as required. My apologises for the confusion that my erroneous figures caused. ciao James 
29th January 2003, 01:35 PM  #6 
diyAudio Member
Join Date: Nov 2002
Location: North Herts, UK

Network truncated the picture first time...

29th January 2003, 03:08 PM  #7 
diyAudio Member

Geez. That's three different equations for Miller cap I've seen *today*!
Tim 
29th January 2003, 03:20 PM  #8 
diyAudio Moderator Emeritus
Join Date: Jan 2003
Location: Near London. UK

James, your derivation from first principles up to Eq. 9 is spot on, and (even more pleasingly) agrees with Ohm's law and the capacitor's reactance at a given frequency.
However, Eq. 10 is rather awkward. Using gmRl is handy for pentodes, but somewhat clumsy for triodes (which, after all, are the ones that have the serious Miller problem). I feel that the following is handier: Cin = Cgk+Cag(1+A): where A is the voltage amplification to the anode
__________________
The loudspeaker: The only commercial HiFi item where a disproportionate part of the budget isn't spent on the box. And the one where it would make a difference... 
29th January 2003, 03:23 PM  #9 
diyAudio Member
Join Date: Nov 2002
Location: North Herts, UK

...the art of assumptions...
Tim,
I given two differnt ones for Miller cap today myself. The first where no reference to a specific circuit applies uses mu as the amplification. The second uses the formal derived expression where gm*R' represents the amplification. The third uses A for the amplification... Three expressions  one meaning...but then you knew that.... All sing chorus "The games people play..." ciao James 
29th January 2003, 03:23 PM  #10 
diyAudio Member
Join Date: Oct 2002
Location: Brooklyn, NY

Uh... ok, james, isn't that what I just said?
Anyway, no, my input calculation is actually correct. In your's you neglect the stray capacitance and Miller effect between cathode and plate. They exist in the 'real world'. Please see the R.D.H.  which is where it is taken directly from. Regardless, when looking at the actual numbers, I think it's pretty clear that the mantra 'you can't overdesign the driver' is silly. Brett, you were right. It is very basic engineering. 
Thread Tools  Search this Thread 


Similar Threads  
Thread  Thread Starter  Forum  Replies  Last Post 
Slew rate calculations  how much do I need?  peranders  Solid State  232  20th November 2011 07:02 PM 
IcePower slew rate  Rikard Nilsson  Class D  24  29th April 2009 05:39 AM 
slew rate adjustment...  chipmonster  Parts  7  25th January 2008 11:01 AM 
Slew rate value  Luke123  Chip Amps  5  7th April 2005 01:30 AM 
slew rate and power output.  JBL  Everything Else  2  16th September 2001 11:51 PM 
New To Site?  Need Help? 