Terminal Strips: Thumbs Up Or Down? Terminal Strips: Thumbs Up Or Down? - diyAudio
Go Back   Home > Forums > > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Tubelab Discussion and support of Tubelab products, prototypes and experiments

Thread Tools Search this Thread
Old 27th October 2014, 02:08 PM   #1
BillEpstein is offline BillEpstein  United States
diyAudio Member
BillEpstein's Avatar
Join Date: Feb 2004
Location: The Great Smoky Mountains
Default Terminal Strips: Thumbs Up Or Down?

My original SSE build was without them figuring eliminating a connector was a good thing. I also didn't quite trust the little screw-downs.

Now that I have removed the wires from the board for the move to the new chassis and ruined more than one eyelet, I'm re-thinking. I like to tinker.

It's also a PITA to get tinned 18ga. into the smallish eyelets.

  Reply With Quote
Old 31st October 2014, 07:28 PM   #2
Steven-H is offline Steven-H  United States
diyAudio Member
Join Date: Jan 2007
Location: The 1st State
Bill -
One option (that I did) was to install turrets into the board. That way I can solder/desolder to the turret instead of the board.
  Reply With Quote
Old 31st October 2014, 09:10 PM   #3
JonSnell Electronic is offline JonSnell Electronic  United Kingdom
diyAudio Member
JonSnell Electronic's Avatar
Join Date: Dec 2012
Location: The Jurassic Coast, England. GB
All older and reliable amplifiers were built with paxolin strip terminal strips. Dead easy to replace components and no through hole pcboard to worry about. Yes most definitely a yes!
Support for Fender, Marshall and all Valve Equipment; Audio Innovations, Audiorama FU29, Quad and Leak. www.jonsnell.co.uk
  Reply With Quote
Old 4th December 2014, 09:57 PM   #4
YashN is offline YashN  Canada
diyAudio Member
Join Date: Dec 2013
Location: Canada
The terminals make it all a bit too fiddly for me: while the principle is very good (you can easily reconfigure the amp), the time taken just to get two wires to stay put in the terminal holes while I screw them in tight is just too much. And it doesn't really work well, until the terminal casing itself gives way...

The holes should be wider.

The turrets seems a good idea.
  Reply With Quote
Old 4th December 2014, 11:39 PM   #5
Andersonix is offline Andersonix  Sweden
diyAudio Member
Andersonix's Avatar
Join Date: Jan 2004
Location: Marin County, California
Terminal Strips: Thumbs Up Or Down?
These Euro style terminal blocks are idiot proof:
  Reply With Quote
Old 5th December 2014, 06:12 PM   #6
denny3249 is offline denny3249  United States
diyAudio Member
denny3249's Avatar
Join Date: Jun 2012
Location: The frozen tundra of Cheeseheadland...
I use the bakelite terminal strips with soldering lugs in almost all my builds and rebuilds.... they come in many configurations...with or w/o ground lugs. Just bend the wire or wires, solder...
  Reply With Quote
Old 13th December 2014, 04:19 PM   #7
Tubelab_com is offline Tubelab_com  United States
diyAudio Member
Tubelab_com's Avatar
Join Date: Jul 2005
Location: West Virginia panhandle
The original TSE board does not use the terminal strips. Many a board has been ruined by a user soldering or unsoldering a transformer wire. Response to the terminal strips has been favorable and I use them in all my projects to make things easier to build and take apart.

There have been no issues, with one exception. I would not use them in the final build of a guitar amp that will spend most of its life sitting on top of the speaker cabinet, especially if it is a bass guitar amp. The constant vibration will cause the screws to loosen over the years.
Tubelab, it's 5 year mission. To explore strange new tubes, to seek out new circuits and topologies, to boldly go where no tube has gone before......
  Reply With Quote


Terminal Strips: Thumbs Up Or Down?Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
2 wires for Return Terminal and 1 wire for (+) Terminal in EXPENSIVE Headphone cable Hallucinogen Headphone Systems 14 24th April 2014 08:21 PM
3 terminal regulator with 3 terminal shunt reference BWRX Power Supplies 11 17th January 2013 09:08 AM
Mounting terminal strips to blank copper board musical noise Construction Tips 9 16th June 2011 06:32 PM
Where Do You Buy Your Terminal Strips? sdclc126 Multi-Way 5 5th June 2007 01:35 PM
Tektronix Silver/Ceramic Terminal/Barrier Strips For Sale Or Trade valveitude Swap Meet 0 23rd January 2006 02:26 AM

New To Site? Need Help?

All times are GMT. The time now is 05:04 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio