Board Availability - Page 15 - diyAudio
Go Back   Home > Forums > Commercial Sector > Vendor Forums > Tubelab

Tubelab Discussion and support of Tubelab products, prototypes and experiments

Reply
 
Thread Tools Search this Thread
Old 9th February 2012, 05:38 PM   #141
diyAudio Member
 
Join Date: Feb 2012
Location: Winder, GA
George, Just paypaled you $108 for the spp board and parts kit last night. Thanks so much, looking forward to receiving it!
  Reply With Quote
Old 9th February 2012, 10:33 PM   #142
diyAudio Member
 
tubelab.com's Avatar
 
Join Date: Jul 2005
Location: West Virginia panhandle
Both will go out tomorrow morning on my way to the Orlando hamfest. I'll be gone for a couple of days.
__________________
Too much power is almost enough! Turn it up till it explodes - then back up just a little.
  Reply With Quote
Old 9th February 2012, 11:44 PM   #143
diyAudio Member
 
Join Date: Jun 2010
Location: Seoul
Hi-fives all around!

I was working on a new preamp when something went down in my power amp (K12g... My first!!!!) that I built a few years ago. I had been planning on building a new amp after finishing up the preamp, but that project got bumped to the top of the list. As I was thinking about what to go with it occurred to me that my girlfriend likes soldering and likes watching me fiddle around with circuit boards (as inept as I am at it), Why not let her build it? At about the same time I saw the SPP board and parts kit... Happy valentines day!!! Ebayed some tubes and I'll get some local iron this weekend.
  Reply With Quote
Old 10th February 2012, 12:44 AM   #144
diyAudio Member
 
tubelab.com's Avatar
 
Join Date: Jul 2005
Location: West Virginia panhandle
Quote:
my girlfriend likes soldering.......Why not let her build it?
When I first started Tubelab (before it was even on the web) I made complete amps and sold them. Most of the buyers never knew that my wife was the person that built the boards.
__________________
Too much power is almost enough! Turn it up till it explodes - then back up just a little.
  Reply With Quote
Old 21st February 2012, 10:48 AM   #145
diyAudio Member
 
Join Date: Jun 2010
Location: Seoul
THe TSE and SPP+parts kit showed up today. 8 business days... Not bad at all for international shipping. I don't know how you got everything in the box (I had trouble repacking it to take home from work after inspecting/drooling over the contents) but everything appears undamaged and ready to go.

The tubes arrived last Friday and we should get the iron later this week. I'll go ahead and move over to the simple pp thread now, but expect pictures and progress of "date night" this weekend
  Reply With Quote
Old 23rd April 2012, 07:11 PM   #146
jacko is offline jacko  United States
diyAudio Member
 
Join Date: Jan 2010
Hi George,

Just paypalled you funds for a 2 SSE's and a SPP and a parts kit. If there are additional shipping charges for the parts kit shipping, please let me know and I'll send it right away.

Btw, missed putting my address in the paypal note. Please check your email add for the address.

Thanks!
  Reply With Quote
Old 21st May 2012, 02:47 AM   #147
zman01 is offline zman01  Bangladesh
diyAudio Member
 
Join Date: Feb 2011
Location: Dhaka
George,

Sorry if this has been answered before -is there a Tubelab SE kit available, or SSE only?
  Reply With Quote
Old 21st May 2012, 01:09 PM   #148
diyAudio Member
 
tubelab.com's Avatar
 
Join Date: Jul 2005
Location: West Virginia panhandle
Quote:
is there a Tubelab SE kit available, or SSE only?
As of today, there is a parts kit for the Simple Push Pull (SPP) only.

The hold up on the SSE kit was the availability of 500 Volt electrolytics. I have several types to try and there will be an SSE kit as soon as I build up a board and test it all. I made some small changes to the SSE board and changed the silkscreened name to avoid legal issues. The new boards are waiting for me when I get home (about 10 days).

The TSE is a problem since there are several different tube choices that require different components. Since it is a DHT amp it can be built with high end parts, or relatively low budget parts. I have seen users put $100 coupling caps in the board, yet I use a $5 cap. Which ones do I put in the kit?

The TSE would require at least two parts kits. I may try to do a mid level 45 kit and a mid level 300B kit in the future, but it will not happen in the near future. My full time engineering job is not leaving me much Tubelab time right now.
__________________
Too much power is almost enough! Turn it up till it explodes - then back up just a little.
  Reply With Quote
Old 21st May 2012, 01:29 PM   #149
zman01 is offline zman01  Bangladesh
diyAudio Member
 
Join Date: Feb 2011
Location: Dhaka
George,

Good to hear from you!

Please give a holler when the SSE Kits are ready! It's better to start simple for me, given my skill level.

- Zia
  Reply With Quote
Old 21st June 2012, 08:32 AM   #150
neomat is offline neomat  France
diyAudio Member
 
neomat's Avatar
 
Join Date: Dec 2011
Location: Somewhere and everywhere
Hi George !

Could it be possible to have SSE kits even without 500V caps ?
It's simplier for you and we spent our time (rather than yours) to look for it...
Have a nice day !
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
2sk1058 availability? AudioGeek Solid State 23 23rd October 2012 05:52 AM
Lagato availability? Jeffrey Davison Twisted Pear 2 29th September 2010 01:12 AM
Tube availability: what would you do? bradd Tubes / Valves 6 27th February 2006 12:40 AM
MDF availability Doug Everything Else 2 24th July 2003 12:04 PM
AD1865N-K availability. Elso Kwak Digital Source 20 21st March 2002 05:59 AM


New To Site? Need Help?

All times are GMT. The time now is 12:16 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2