Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

The Lounge A place to talk about almost anything but politics and religion.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 26th April 2013, 11:29 PM   #1
Dan Kelly is offline Dan Kelly  United States
diyAudio Member
Join Date: Apr 2013
Default Meanings

What do they mean by 1/3 and 2/3 octive? What do they mean by balanced and unbalanced you see it a lot on the back of E/Qs?
  Reply With Quote
Old 27th April 2013, 12:11 AM   #2
bear is offline bear
expert in tautology
diyAudio Member
bear's Avatar
Join Date: Apr 2002
Location: New York State USA
an octave is a doubling of frequency.

A-440Hz is middle A, so 2x that frequency or 880Hz. is one octave up.
Half an octave is for this frequency 440 + 220Hz or 660 Hz.
Similarly 1/3 is dividing that octave into thirds.
2/3rd of an octave is 2x 1/3 of that octave above some frequency.

This usually refers to smoothing or the bandwidth of an EQ adjustment.

In the case of smoothing, all the energy on either side of a center frequency (decided in the hardware or software) is averaged and that output is what is shown or adjusted (respectively for measurement or smoothing). For measurement this yields a smoother and flatter looking response.

Fully unsmoothed response curves have lots and lots of ups and downs, so this makes it easy to see the trend... of course overly smoothed curves make things look better than they are and could possibly ignore some actual response anomaly.

Balanced means that there is a dual polarity signal plus ground. Three wires. Unbalanced means a single polarity signal and ground.

Typically the balanced connector is an XLR or a TRS phone plug (3 wire or "stereo" 1/4" phone plug). The unbalanced is typically an RCA plug or else a mono 1/4" phone plug (tip and sleeve - two wires).

Balanced is associated more with pro gear. The balanced line gives better immunity from hum and noise, especially on longer runs, and if true professional design is "600 ohm" meaning it runs lower Z which helps prevent HF rolloff - again better on longer runs.


http://www.bearlabs.com -- Btw, I don't actually know anything, FYI -- every once in a while I say something that makes sense... ]
  Reply With Quote
Old 27th April 2013, 12:37 AM   #3
Dan Kelly is offline Dan Kelly  United States
diyAudio Member
Join Date: Apr 2013
Thanks Bear, for clearing that up for me
  Reply With Quote
Old 8th May 2013, 06:55 PM   #4
Wavebourn is offline Wavebourn  United States
Designer & Technologist
diyAudio Member
Wavebourn's Avatar
Join Date: Sep 2006
Location: Pleasant Hill, CA
Some meanings are so hidden in the plain sight..

Click the image to open in full size.
The Devil is not so terrible as his math model is!
  Reply With Quote


MeaningsHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

New To Site? Need Help?

All times are GMT. The time now is 03:18 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio