diyAudio

diyAudio (http://www.diyaudio.com/forums/)
-   Swap Meet (http://www.diyaudio.com/forums/swap-meet/)
-   -   Aleph 2 Boards Ordered (http://www.diyaudio.com/forums/swap-meet/6104-aleph-2-boards-ordered.html)

harvardian 17th September 2002 07:42 PM

Aleph 2 Boards Ordered
 
Hello All,

I have ordered 50 Aleph driver boards using BrianGT's layout. Here is the pricing:


2 Boards - USD $45 including US/CA shipping

These will have silkscreen, solder mask, 2.5 Oz copper,
.093" thickness. This is a single sided board.

Output Boards are not ordered yet. If there is enough interest, the cost will be $45.00 for a set of four (six output devices).

The cost will be USD $85 for the complete set.

Shipping outside of US will add $5-$10.

Please reserve boards by email to dherman@ksaria.com
Payment can be by Paypal (dherman@ksaria.com, add 4%)
or by check/MO.
Dale Herman
44 Myrick Lane
Harvard, MA 01451


P.S. I also have some fets left if anyone is interested in them as well. I have decided not to buy any heat sinks. The price from M&M is pretty good, and they do not seem to want to make other extrusions. There is also not much quantity discount.

I would be willing to buy other components such as zeners, resistors, caps and such.

harvardian 20th September 2002 11:22 AM

Will include Q package FREE
 
Hi Guys,

I don't want to be stuck with these boards, so I'll include a full set of semiconductors including:

6 IRF9610 - two pairs matched plus two for current source

10 Zener diodes

2 MPSA18


For anyone that has already ordered, I will include as well. If you don't need them, please indicate.

Best Regards,

Dale

P.S. The output boards will be cheaper than I thought, should be able to ship for $35/4

Narcisse91 20th September 2002 11:47 AM

The way the output boards are set up, is a set of four good for two monoblocks?

At that price, I think I'll grab some of those too. I want the PCBs for four monoblocks. You have me down for two pairs of driver boards (under my assumed name of Mike Reda). Will I need two sets of four?

Mike

harvardian 20th September 2002 11:53 AM

Hi,

I will try to post some drawings of the output boards today. They will be just like the Wayne Sankey layout.

On each board, there is space for six mosfets, the six 1 Ohm resistors, and the gate drive resistors. You use flying leads to attach to the driver board.

These will NOT have soldermask and silkscreen. Don't really need and keeps costs much lower.

The board size is 1.6" X 8".

They will have 2.5 Oz copper. I have made the traces quite wide.

Dale

harvardian 25th September 2002 07:11 PM

Output board layout
 
2 Attachment(s)
Sorry for the delay. Family illness. I will order these today if no one sees a problem.

Note, These will not have silkscreen and soldermask unless you want to spend the $$

They will be plated (not bare copper)

Dale

Narcisse91 25th September 2002 07:51 PM

Is there a specific parts list somewhere that this was created for? The layout uses specific parts which will have specific footprints, so I'd like to make sure any parts I order will fit without problems.

Mike

harvardian 25th September 2002 08:18 PM

For the 1Ohm 5W resistor:

http://www.mouser.com/catalog/specsheets/71RS.pdf
71-RS5-1

For the gate resistor:

221 Ohm 1/4W

Almost anything:

BC221XCT-ND (At www.digikey.com)

And of course IRFP240 Mosfets

Hope this helps.

Best Regards,

Dale

MEnsing 26th September 2002 05:35 AM

Quote:

I will order these today if no one sees a problem.
They are looking good!! :) I'm in for 2 sets.

harvardian 26th September 2002 03:12 PM

Updated output board
 
2 Attachment(s)
Thanks to fcel (Roderick), I have updated the board for those that want to do an Aleph 5.
Basically, I added a second set of connection points, so that the board could be cut in half. Also, I have added labels (in bottom copper) for the connections to the driver boards.


By the way, I ordered the boards today with a two week turn.
I apologize for any delays that this causes. For those that ordered both driver and output, please contact me if you would like the driver boards ahead of the output boards. If you don't really need right away, I would rather wait (save on mailing costs). For anyone that ordered just the driver boards, I will send out as soon as they arrive (scheduled to ship from board vendor on 10/01).

Best Regards,

Dale

fcel 27th September 2002 01:11 AM

Dale ... I can wait.


All times are GMT. The time now is 06:23 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio


Content Relevant URLs by vBSEO 3.3.2