Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Swap Meet Sell your stuff here, who knows, some other fanatic might be interested!

FS: Carvin DCM600 power amp 600watt RMS
FS: Carvin DCM600 power amp 600watt RMS
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Closed Thread
Thread Tools Search this Thread
Old 22nd February 2002, 06:16 PM   #1
Gomer is offline Gomer
diyAudio Member
Join Date: May 2001
Thumbs up FS: Carvin DCM600 power amp 600watt RMS

I am selling my Carvin amp for the single reason that I got a good deal on a Crown K2. The carvin amp has a few months of light use on it for my home theater subwoofer. If I didn't tell you other wise, you'd swear it was brand new!

I am asking $250 (shipping included) obo. If you are in southern california and are willing to pick it up, make it $225 (I am at UCI). This amp is normally $337 + tax.

Some specs
NOTE: RMS as in run it all day at these levels without any problems type RMS

Bridged Continuous RMS:
4 ohms 600watts
8 ohms 450watts

Both Channels Continous RMS
2 ohms 300watts/ch
4 ohms 250watts/ch
8 ohms 125watts/ch

Frequency Response: ±0.5 dB, 20 Hz to 20kHz (±1.5 dB, 10 Hz & 40 kHz)
THD (1/2 power): 0.03% 0.03%
Damping Factor: >350 >400
Slew Rate: bridged mode >45v/΅s >45v/΅s
Sensitivity: (4ohms, Vms) 1.0 V 1.0 V
Signal to Noise Ratio: Above 100 dB
Input Impedance: >20K ohms, balanced

Protection Circuits: • Short Circuit • No Load Protection • SpeakerGuard™ • Thermal Shut-Off
• Mute On/OFF

Control and Indicators:
Front: • Power switch • Recessed detent attenuators • Signal LED • Clip LED • Protect LED • Power Indicator

Rear: Ground Lift (each channel) • Parallel Input Switch • Speaker Output Bridge Switch • Limiters IN/OUT Sw • Input Connectors: Two each; Balanced XLR & 1/4” • Speaker Output Connectors: 3 Twist-Lok, heavy-duty binding posts and two 1/4” phone jacks

Dimensions: 3 1/2" High x 10" Depth x 19" Wide (2-space)

Closed Thread

FS: Carvin DCM600 power amp 600watt RMSHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
carvin x-100B engel dela pena Instruments and Amps 4 12th October 2007 12:47 PM
wtb Carvin v3 amplifier gemm012 Swap Meet 1 11th December 2006 03:01 PM
REQ: Schematic for Carvin DCA 800 Bargainhunter Solid State 1 1st March 2005 02:47 AM
Carvin DCA 800, only NPN? cm961 Solid State 5 24th October 2002 03:34 AM

New To Site? Need Help?

All times are GMT. The time now is 03:02 AM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio