FS: DC regulator boards for 2A3 (or other) filaments - diyAudio
Go Back   Home > Forums > Commercial Sector > Swap Meet

Swap Meet Sell your stuff here, who knows, some other fanatic might be interested!

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 11th October 2003, 08:33 PM   #1
diyAudio Member
 
Join Date: Sep 2002
Location: Oregon, USA
Default FS: DC regulator boards for 2A3 (or other) filaments

Hi,

Up for sale are a pair of boards I built to provide a DC regulated filament supply for my 2A3s. I did this mainly to try and reduce hum in my amp, and it didn't really do that (which means my hum is from other sources, not the filaments). The ICs generate a fair amount of heat and the underside of my amp is getting crowded, so I decided to go back to AC. The current regulated filaments sounded a little quieter and smoother, but I didn't want to put in the chassis/construction work required to ensure adequate ventilation.

The boards use MBR735 high current Schottky diodes, Elna electrolytic caps, and LT1085 adjustable regulators. You can configure this to be a voltage or a current regulator, depending on how you wire it to the sense resistor and the filaments (I can help you with the circuit connections and values if you want). I also have a pair of Hammond 6.3V/4A transformers that I used to power these with. A 2A3 filament takes 2.5V/2.5A, and these could supply that easily.

Click the image to open in full size.

Click the image to open in full size.

Click the image to open in full size.

Click the image to open in full size.

The circuits are built on Radio Shack PCBs, but I used point-to-point wiring so the PCB traces aren't carrying the 2.5A of current. You'll need to connect the transformers to the diode bridge, and the regulator to an external sense resistor and the filaments. You can also add a resistor between the capacitors to make a CRC filter, right now I just have both caps in parallel.

A list of the parts you'll get:

2x Hammond 166N6 filament transformers - 115V pri, 6.3V 4A CT sec (center tap wire has been trimmed and heat-shrink covered, but there's enough left over to solder to should you need it)
8x MBR735 35V 7.5A Schottky diodes with heatsinks
2x LT1085 3A adjustable voltage regulators with heatsinks
4x Elna 3300uF 35V capacitors

And as I said, I can help you with connecting this up (it's really easy to do).

I have about $70 in parts here. Asking for $40 shipped anywhere in the US or Canada, with free email consultation for any help you might need with these

If you've been thinking of trying DC current regulated filaments for your DHTs, here's your chance. I've already done all of the hard work, all you need to do is add these boards to your amps and solder a few connections.

Thanks for looking,
Saurav
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
alw regulator circuit boards fmak Solid State 1 3rd December 2008 04:11 PM
CCS Design for DHT Filaments dsavitsk Tubes / Valves 9 29th April 2008 06:56 PM
Regulator boards (on ebay) Nathan A. Swap Meet 0 2nd June 2006 11:28 PM
FS: TO-220 regulator boards BWRX Swap Meet 41 6th April 2006 03:03 PM
Filaments for the Aikido Kashmire Tubes / Valves 1 2nd August 2005 01:24 PM


New To Site? Need Help?

All times are GMT. The time now is 02:43 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2