FS: Moving sale, lots of goodies

[JoshK]

So in anticipation of a moving, I've gone through a vast collection of mostly unfinished projects and some chassis. I'll keep updating this thread with stuff as I uncover more.

1) UcD400 4 channel amp unfinished. Parmetal black alum anon chassis. Antek AN-7239 toroid (39V/0/39). DIYCable powersupply with Panasonic caps. Four UCD 400 AD8620 modules. XLR inputs, Speakon speaker connectors, Powercon power input, Thermal breaker power switch (in lieu of a fuse). Needs to be wired up with connections between all the stuff. $650

2) Behringer CX-2310 analog crossover, stereo 2way or mono 3way. $60

3) CD-Pro2 transport. These were the ones from many years ago that were being sold as a kit. This kit was built by the guy selling the kits (Ken I think). He sold it to me saying the reviewer said that there were a couple issues with it. Having built two of these before, I suspect that the CD sensor wasn't set up quite right. He sold me the built kit along with enough of the boards/parts to rebuild any and every board in it. (no additional transport mechanism or case). Buyer would need to test it out, troubleshoot and possibly rebuilt a board with supplied parts. Has remote. The lid is wrapped up but provided. $400

4) Sansui Solid State 800. possibly dead. I had bought this, it worked but the knobs where very scratchy/intermittant. I opened it up and started to clean out the switches. It worked for a while and then suddenly it won't power on. I suspect the power switch is bad, but its a gamble. Free, but not very motivated to box and ship, so local is better.

5) silver aluminum preamp chassis. comes with extra faceplate. $100

6) black par-metal aluminum chassis. used in my first ever tube preamp project but was noisey as I built it, so I took it apart. the chassis is pretty uglied up but could be made to be very useful for the creative person. $30

[JoshK]

The first post has pictures of the UcD 4ch amp.

Here is the transport:

[JoshK]

behringer cx

[JoshK]

silver preamp case

[JoshK]

Sansui receiver

[JoshK]

uglified parmetal black preamp case

[JoshK]

much more goodies...
7) box of tungsol tubes... most likely tv repair. not any obvious pairs. say $15.

[JoshK]

8) Silk Audio TVC preamp. Par-metal large steel chassis. 3 Sieden switches. 6 inputs, 2 bypass inputs, two outputs (although I can't recall if second output is wired currently). RCAs are top quality ones from vt4c.com. Black Cherry 1" thick faceplate, unfinished, had planned to engrave/burn, but couldn't find the pattern for the letters I wanted. Long extention shafts to keep wiring short. Silver wiring. Lots of room for adding active stage that had been planned. Hole drilled in back for powercon input. Headphone jack on front. Large knobs. $700

[JoshK]

9) UcD 400 AD8620 monoblocks. All high end parts: Plitron transformers 500VA, dual IXYS bridges, 4 Jensen 4pole caps, bulgin switch, rod's switch kit, softstarts, ying/yang ground, XLR inputs, Speakon connectors, powercon and normal power input. Fancy chassis which cost a pretty penny to ship from Thailand.

The are all hooked up except for the switch. My idea of driving a relay didn't work. buyer would need to figure out method. I can see if I can find the details of the board I used. Its marked Amp Turn On V1.1b RCC Dec-2005.

Not super excited to part with these but have WAY too much stuff to move. Considering the parts quality, I have roughly $1400 invested. Asking $1000.

[JoshK]

10) DIY Teres plinth. Made from maple chopping blocks, PVC, lead shot and solid oak armboard. brass cone footers. This was my original plinth before I bought a slate plinth. Doesn't come with the rest of the kit, that you provide. Arm drilled for Rega 300 arm. Free but *have to pick up*. I am not shipping, sorry.