AKIDO Line Stage with PEARL CryoValves & Coolers and Stepped Attenuator

Mother of PEARL · 03:35 AM

Guys:
I have a fully assembled, tested and -unused- 2005 vintage Akido linestage board that uses very closely matched, low noise PEARL CryoValve ECC99s, IAR Wonder Caps in the signal path, RelCap PS bypass caps, Cardas solder and decent, generic RCA connectors for testing purposes.
The ECC99s are fitted with PEARL tube coolers. Tube coolers and CryoValves can be seen on our here on our site: PEARL's Products & Services and do note the 1 year sliding scale warranty on CryoValves, just follow the on-page links to get to it.
Also offered is the low-cost-switch version of Broskie's three switch volume control, also fully assembled.

For the pre-amp with tubes, coolers, caps and full warranty on the tubes I am asking $US400.00 and for the volume control wired, tested and -unused- $US35.00.
PayPal is the payment method please. Pix to follow if requested . . .

Bill P. @ PEARL

merlin el mago · 3rd November 2010, 11:47 AM

Please give more information about the volume control is 100K or 20K? is this one:

Wich resistors are installed: Vishay, Caddock, etc.?

Mother of PEARL · 3rd November 2010, 05:12 PM

Essentially, it is the board above. The switches are the same but the trace layout is a bit different. It is the 100K version and the resistors are whatever Broskie was supplying at the time, Coddack I believe. The resistors' body color is baby blue

3rd November 2010, 03:34 AM	#1
Mother of PEARL diyAudio Member Join Date: Mar 2010 Location: Calgary, Ab, Canada	AKIDO Line Stage with PEARL CryoValves & Coolers and Stepped Attenuator Guys: I have a fully assembled, tested and -unused- 2005 vintage Akido linestage board that uses very closely matched, low noise PEARL CryoValve ECC99s, IAR Wonder Caps in the signal path, RelCap PS bypass caps, Cardas solder and decent, generic RCA connectors for testing purposes. The ECC99s are fitted with PEARL tube coolers. Tube coolers and CryoValves can be seen on our here on our site: PEARL's Products & Services and do note the 1 year sliding scale warranty on CryoValves, just follow the on-page links to get to it. Also offered is the low-cost-switch version of Broskie's three switch volume control, also fully assembled. For the pre-amp with tubes, coolers, caps and full warranty on the tubes I am asking $US400.00 and for the volume control wired, tested and -unused- $US35.00. PayPal is the payment method please. Pix to follow if requested . . . Bill P. @ PEARL Last edited by Mother of PEARL; 3rd November 2010 at 03:35 AM. Reason: Typo

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
stepped attenuator	onno	Pass Labs	20	25th September 2007 09:04 PM
Balanced line stage- input or output attenuator	nobody special	Pass Labs	4	7th April 2006 01:18 PM
stepped attenuator	ivegotmono	Tubes / Valves	4	7th January 2006 02:49 PM
Stepped Attenuator	officeboy	Parts	3	6th May 2004 03:32 PM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

3rd November 2010, 11:47 AM	#2
merlin el mago diyAudio Member Join Date: Sep 2009 Location: Catalonia new Europe state	Please give more information about the volume control is 100K or 20K? is this one: Wich resistors are installed: Vishay, Caddock, etc.?

3rd November 2010, 05:12 PM	#3
Mother of PEARL diyAudio Member Join Date: Mar 2010 Location: Calgary, Ab, Canada	Essentially, it is the board above. The switches are the same but the trace layout is a bit different. It is the 100K version and the resistors are whatever Broskie was supplying at the time, Coddack I believe. The resistors' body color is baby blue