WTB a few RCA shoulder washers

Renron · 4th February 2009, 02:46 PM

Well Hidee-Ho.... to all my friends in Audio land,

At Burning Amp '07 Papa was nice enough to give me (I took 'em)
a set of 8 RCA chassis jacks mounted to an aluminum plate. Thanks PaPa! But I need 4 shoulder (isolation) washers to build them into my Aikido Preamp. I really don't want to buy 100 of these just for few I need.
Anybody have a few they would like to sell off and help a brother out?
I'm not sure if there is a standard size to the threaded barrel but these measure .31" or just under 8mm.

I know I could mount them on a thin sheet of ABS or Plexiglas but I want it to look professional.
Other ideas welcomed with appreciation.
Sacramento CA
Ron

Geek · 4th February 2009, 08:53 PM

Are your jacks needing 1/4" holes?

I have a few Keystone #4711 fibre shoulder washers here.

Cheers!

Renron · 5th February 2009, 12:18 AM

Geek,
Yes, 1/4" would work, if you have 4 you could spare that would be great. How much would you like for them? Trade perhaps? I'll send you 2 brand new in the wrapper Westcap .33uF PIO caps? They look like they could be twins of Vitamin Qs. I have not heard them as they were purchase for my Preamp build. I bought extras

Ron

Renron · 5th February 2009, 12:27 AM

Geek,
I just Google mapped your city, not that far from a small lot I owned for a short time. Just across the straights from you in Nanaimo. What a wonderful place that was, Nice people too. I miss the pine trees.

Wifee and I lived at Lake Tahoe for 20 years, same kind of place and kind folks.

Ron

Geek · 5th February 2009, 02:57 AM

Hi Ron,

It's a trade

Let's trade addresses: geek <at> scorpiorising <dot> ca

Nanaimo is a fair distance from me actually, but any property on the "Republic of Vancouver Island" ( (tm) chrisb

) is pretty much worth a fortune, recession or not.

Cheers!

Renron · 7th February 2009, 12:27 AM

Gregg,
They go out tomorrow, family came over today and didn't get to the mail. Tomorrow for sure!

Ron

Geek · 7th February 2009, 03:52 AM

No worries mate! Got yours out today

Cheers!

4th February 2009, 02:46 PM	#1
Renron diyAudio Member Join Date: Jan 2007 Location: Sacramento	WTB a few RCA shoulder washers Well Hidee-Ho.... to all my friends in Audio land, At Burning Amp '07 Papa was nice enough to give me (I took 'em) a set of 8 RCA chassis jacks mounted to an aluminum plate. Thanks PaPa! But I need 4 shoulder (isolation) washers to build them into my Aikido Preamp. I really don't want to buy 100 of these just for few I need. Anybody have a few they would like to sell off and help a brother out? I'm not sure if there is a standard size to the threaded barrel but these measure .31" or just under 8mm. I know I could mount them on a thin sheet of ABS or Plexiglas but I want it to look professional. Other ideas welcomed with appreciation. Sacramento CA Ron __________________ "If it doesn't work properly, hope it catches on fire"- Nelson Pass @ BA3 "I fired up the prototype. Literally." The Prophet Pass.

5th February 2009, 12:18 AM	#3
Renron diyAudio Member Join Date: Jan 2007 Location: Sacramento	Geek, Yes, 1/4" would work, if you have 4 you could spare that would be great. How much would you like for them? Trade perhaps? I'll send you 2 brand new in the wrapper Westcap .33uF PIO caps? They look like they could be twins of Vitamin Qs. I have not heard them as they were purchase for my Preamp build. I bought extras Ron __________________ "If it doesn't work properly, hope it catches on fire"- Nelson Pass @ BA3 "I fired up the prototype. Literally." The Prophet Pass.

7th February 2009, 12:27 AM	#6
Renron diyAudio Member Join Date: Jan 2007 Location: Sacramento	Gregg, They go out tomorrow, family came over today and didn't get to the mail. Tomorrow for sure! Ron __________________ "If it doesn't work properly, hope it catches on fire"- Nelson Pass @ BA3 "I fired up the prototype. Literally." The Prophet Pass.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Rubber washers on TRANSFORMERS???	kyrie48	Solid State	5	9th November 2007 08:16 PM
Do standard TO-220 washers fit an LM3886T?	wintermute	Chip Amps	11	14th August 2006 06:10 PM
painted heatsinks & insulating washers	lowlevel	Solid State	74	22nd June 2005 07:51 AM
Conical spring washers ??	sam9	Parts	11	24th June 2004 09:17 PM
For want of a shoulder washer...	OddOne	Solid State	0	10th March 2004 02:09 AM


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

4th February 2009, 08:53 PM	#2
Geek diyAudio Member Join Date: Sep 2004	Are your jacks needing 1/4" holes? I have a few Keystone #4711 fibre shoulder washers here. Cheers!

5th February 2009, 12:27 AM	#4
Renron diyAudio Member Join Date: Jan 2007 Location: Sacramento	Geek, I just Google mapped your city, not that far from a small lot I owned for a short time. Just across the straights from you in Nanaimo. What a wonderful place that was, Nice people too. I miss the pine trees. Wifee and I lived at Lake Tahoe for 20 years, same kind of place and kind folks. Ron __________________ "If it doesn't work properly, hope it catches on fire"- Nelson Pass @ BA3 "I fired up the prototype. Literally." The Prophet Pass.

5th February 2009, 02:57 AM	#5
Geek diyAudio Member Join Date: Sep 2004	Hi Ron, It's a trade Let's trade addresses: geek <at> scorpiorising <dot> ca Nanaimo is a fair distance from me actually, but any property on the "Republic of Vancouver Island" ( (tm) chrisb ) is pretty much worth a fortune, recession or not. Cheers!

7th February 2009, 03:52 AM	#7
Geek diyAudio Member Join Date: Sep 2004	No worries mate! Got yours out today Cheers!

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read