Chipamp heatsink

HIPCHECK · 4th March 2008, 04:38 AM

Does anybody want this item? It should fit your standard LM3886 or OPA549 amp, etc.

was planning to use lexan/plexi over the chip to "see the guts"

It has 2 holes that pass thru and 1 is drilled for a XLR panel mount plug. the other was going to be a speakon plug or 1/4 jack for speaker out. the slot on the front was to pass the power supply wires thru. 2 holes not shown in the pics are drilled for power supply caps to be "dropped into" to help with p2p wiring. the tapped holes are not too great, but im sure you can make this into a great little amp!

if you want them just pay shipping, unless you want to trade/give me some of your left overs then i'll ship to you free

Stevehttp://www.diyaudio.com/forums/showt...10#post1031010

HIPCHECK · 4th March 2008, 10:26 PM

please scroll down to see pictures of cleaned up unit in attached post.

bichi · 6th March 2008, 09:54 AM

HIPCHECK,

I'll put those wonderful chunks of aluminium to use!
- I'm a new user and under moderation and can't PM you.
- willing to trade the small switcher described below. (ordered too many a few years ago...)
- located in Silicon Valley, USA.
- hopefully, PM will activate for me, after this post

TOKO 10W MULTI-OUTPUT POWER SUPPLY - ET10-21
- DigiKey: TS9961-ND

Picture:
http://www.esnips.com/doc/354338aa-a...12-0.3A_-5-0.1

4th March 2008, 04:38 AM	#1
HIPCHECK diyAudio Member Join Date: Jun 2004 Location: ARKANSAS	Chipamp heatsink Does anybody want this item? It should fit your standard LM3886 or OPA549 amp, etc. was planning to use lexan/plexi over the chip to "see the guts" It has 2 holes that pass thru and 1 is drilled for a XLR panel mount plug. the other was going to be a speakon plug or 1/4 jack for speaker out. the slot on the front was to pass the power supply wires thru. 2 holes not shown in the pics are drilled for power supply caps to be "dropped into" to help with p2p wiring. the tapped holes are not too great, but im sure you can make this into a great little amp! if you want them just pay shipping, unless you want to trade/give me some of your left overs then i'll ship to you free Stevehttp://www.diyaudio.com/forums/showt...10#post1031010 __________________ If a inch of duct tape will fix it, 3 feet should fix it for life!!!!

4th March 2008, 10:26 PM	#2
HIPCHECK diyAudio Member Join Date: Jun 2004 Location: ARKANSAS	please scroll down to see pictures of cleaned up unit in attached post. __________________ If a inch of duct tape will fix it, 3 feet should fix it for life!!!!

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
My chipamp	zymurgn	Chip Amps	25	3rd December 2008 05:29 PM
My first Chipamp	Trooper46	Chip Amps	18	7th November 2008 01:25 PM
Appropriate chipamp for HT2	paean	Chip Amps	11	8th February 2008 08:15 PM
chipamp ccs	elmar	Pass Labs	0	14th December 2006 04:04 PM
chipamp.com	renfrow	Chip Amps	14	11th August 2006 08:10 AM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

6th March 2008, 09:54 AM	#3
bichi diyAudio Member Join Date: Aug 2007	HIPCHECK, I'll put those wonderful chunks of aluminium to use! - I'm a new user and under moderation and can't PM you. - willing to trade the small switcher described below. (ordered too many a few years ago...) - located in Silicon Valley, USA. - hopefully, PM will activate for me, after this post TOKO 10W MULTI-OUTPUT POWER SUPPLY - ET10-21 - DigiKey: TS9961-ND Picture: http://www.esnips.com/doc/354338aa-a...12-0.3A_-5-0.1

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)