FS- Scan-Speak MTM 8546/9300

BDP · 29th April 2007, 04:23 AM

Scan-Speak MTM with 18W8546 Kevlar mid woofers and 2905/9300 tweeters. North Creek components. Cherry veneer. Asking $525. Can be seen and listened to in Vancouver Washington, USA.

BDP · 29th April 2007, 06:04 AM

Here is a frequency response measurement.

Spasticteapot · 29th April 2007, 02:59 PM

Hot diggity!

If I lived a bit closer, I'd probbably buy those.

Furocious · 1st May 2007, 03:47 AM

woud you be willing to part them out and sell the drivers and crossovers?

BDP · 1st May 2007, 04:15 AM

Yes, they could be parted to save shipping. It would be a shame, the cabinets are nice.

Here is the antiphase response.

Furocious · 1st May 2007, 01:48 PM

yeah, I love the cabinets, but it would be far too expensive for me to ship them... plus I have some cabinets I'm looking to add drivers too.

Can you give me/email me more info on these speakers? What type of cabinet they are in/ what could they fit in, did you design the crossovers or were they purchased somewhere?

Since you're willing to part these out, would you go down on the price?

thanks

BDP · 2nd May 2007, 04:20 AM

Iam unable to send an e-mail to you via DIY. You could e-mail me .
The cabinets are ported and I did the x-overs using IMP audio Analyzer.

mathman · 2nd May 2007, 06:21 PM

Great deal! I have some monitors with the 18w-8546 and love that driver. Mine use the less expensive 2010 tweet though, which isn’t nearly as impressive as the 2905-XXXX tweets.

Would you mind sharing the crossover schematic? I’d also be interested in the specifics of crossover components, such as gauge size and type (air/iron) of the inductors, if you used bypass caps etc. If you prefer to send an email, mine should be visible in my profile.

Any details on cabinet construction? Material, bracing etc would be helpful if you know. Perhaps you used North Creek’s recommended builder, Lee Taylor, or are these DIY?

Would you ship the whole thing to Colorado? I am interested in just the drivers and crossovers, but if we could ship the cabinets for a sane amount that would be great.

BDP · 3rd May 2007, 05:24 AM

A closer look at the drivers.

mathman · 3rd May 2007, 03:04 PM

Hey BDP, thanks for the info: I bounced you an email so keep an eye on your junk folder.

One more question: can the crossovers be accessed without cutting? Just curious.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Scan Speak 23W sub	Pan	Subwoofers	15	26th December 2007 06:13 PM
M1 Xover With Ss 9300/8546?	cliffylfd	Multi-Way	0	22nd October 2007 11:32 PM
Scan Speak 15M	Jed	Multi-Way	27	23rd March 2007 07:45 AM
scan-speak 9300 problem	macgyver	Multi-Way	1	14th November 2003 01:22 PM
Scan-speak M1 (again..)	macgyver	Multi-Way	0	31st October 2002 08:39 AM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

29th April 2007, 02:59 PM	#3
Spasticteapot diyAudio Member Join Date: Jan 2006 Location: Wisconsin....what did you expect?	Hot diggity! If I lived a bit closer, I'd probbably buy those.

1st May 2007, 03:47 AM	#4
Furocious diyAudio Member Join Date: Feb 2006 Location: Omaha	woud you be willing to part them out and sell the drivers and crossovers?

1st May 2007, 01:48 PM	#6
Furocious diyAudio Member Join Date: Feb 2006 Location: Omaha	yeah, I love the cabinets, but it would be far too expensive for me to ship them... plus I have some cabinets I'm looking to add drivers too. Can you give me/email me more info on these speakers? What type of cabinet they are in/ what could they fit in, did you design the crossovers or were they purchased somewhere? Since you're willing to part these out, would you go down on the price? thanks

2nd May 2007, 04:20 AM	#7
BDP diyAudio Member Join Date: Apr 2002 Location: Washington State	Iam unable to send an e-mail to you via DIY. You could e-mail me . The cabinets are ported and I did the x-overs using IMP audio Analyzer.

2nd May 2007, 06:21 PM	#8
mathman diyAudio Member Join Date: Feb 2006 Location: Colorado	Great deal! I have some monitors with the 18w-8546 and love that driver. Mine use the less expensive 2010 tweet though, which isn’t nearly as impressive as the 2905-XXXX tweets. Would you mind sharing the crossover schematic? I’d also be interested in the specifics of crossover components, such as gauge size and type (air/iron) of the inductors, if you used bypass caps etc. If you prefer to send an email, mine should be visible in my profile. Any details on cabinet construction? Material, bracing etc would be helpful if you know. Perhaps you used North Creek’s recommended builder, Lee Taylor, or are these DIY? Would you ship the whole thing to Colorado? I am interested in just the drivers and crossovers, but if we could ship the cabinets for a sane amount that would be great.

3rd May 2007, 03:04 PM	#10
mathman diyAudio Member Join Date: Feb 2006 Location: Colorado	Hey BDP, thanks for the info: I bounced you an email so keep an eye on your junk folder. One more question: can the crossovers be accessed without cutting? Just curious.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)