Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

anyone ever run PE 1000W plate amp at 3 ohms?
anyone ever run PE 1000W plate amp at 3 ohms?
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 29th July 2005, 01:01 AM   #1
derekwwww is offline derekwwww  Canada
diyAudio Member
Join Date: Jan 2005
Location: CANADA
Default anyone ever run PE 1000W plate amp at 3 ohms?

I know they say not to run theie amps at anything less then 4 ohms but I was wondering if anyone has ran them at anything less then 4 ohms, say 3 ohms, without or with problems? Right now I have two DVC 2 ohm subs wired into an 8 ohm load on the amp so the subs are getting around 270 watts each. I have a 3rd sub of the same kind sitting here and if I built a box for it and wired it in I could wire the three to a 3 ohm load, and then the subs would be getting more like 350 watts each or more. Also these subs are rated 350W RMS so it would drive them better then it does now. Anyways, I would just like to hear if anyone has tried this with their 1000W plate amp or even their 500W plate amp. Thanks...
  Reply With Quote
Old 29th July 2005, 10:47 AM   #2
simon5 is offline simon5  Canada
diyAudio Member
Join Date: Nov 2004
Location: Québec, Québec
Well, I used a 250W Rythmik Audio amplifier for a Shiva, which is essentially a modded PartsExpress amplifier. The Shiva is rated at 2.9 ohms Re, and in the box there's a low at about 3.65 ohms at 18.5 Hz and 2.95 ohms at around 110 Hz. They said to use drivers with Re higher than 3.0.

If the subwoofer is playing alone with the crossover knob set at 160 Hz, I can shut the amplifier down without going into overexcursion. Overcurrent protection I guess.

Your amplifier probably got that protection too, so I would not be worried by that. Just start with gain low, and climb until the amp don't shut down too much. I guess at 3 ohms your amplifier will be current limited, so don't expect more than 768W RMS output. ( 64V x 16A = 1024W at 4 ohms then 48V x 16A = 768W at 3 ohms )
DIYaudio for President !
  Reply With Quote


anyone ever run PE 1000W plate amp at 3 ohms?Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
WANTED: Subwoofer Plate Amplifier (500W RMS / 4 Ohms) ViperZ Swap Meet 1 1st February 2010 03:36 AM
FS: Keiga KGND-52100 1000w Icepower subwoofer plate amps shokunin Swap Meet 3 7th October 2007 04:56 PM
ISOBARIC 16 ohms load powered by 8 ohms Amp eddi0 Subwoofers 24 21st October 2006 04:29 PM
Speakers: 8 ohms vs. 16 ohms KT Multi-Way 2 14th April 2006 06:06 PM
Plate Amp Standby Current (PE 500W/1000W) gmikol Subwoofers 6 20th February 2006 07:19 AM

New To Site? Need Help?

All times are GMT. The time now is 04:05 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio