Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Should I keep these ports separated?
Should I keep these ports separated?
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 14th December 2003, 07:44 PM   #1
Stephen D is offline Stephen D  United States
diyAudio Member
Join Date: Dec 2003
Location: In a house
Default Should I keep these ports separated?

I'm building a simple 2 driver ported sub cab. The box will have a divider (as is commonly recommended) to separate the drivers into their own volumes to ensure any driver response mismatches don't effect the volume seen by each. It's occurred to me that similar consideration might should be applied to the ports. The ports for this cab must be font firing (exit speaker baffle). I'm wondering if the ports for the individual box volumes should be positioned right next to each other (where the 2 separate enclosures join) or if it would be better to position them at opposite far ends of the front baffle to theoretically minimize any interactive air load effect they may have on each other do to slight tuning mismatches, or if it doesn't matter one doodly squat. Remember these are separate ports of separate enclosures.

In the absence of knowledge opinions are welcome.
You thought I had it!?... I thought you had it!
  Reply With Quote
Old 14th December 2003, 08:21 PM   #2
HiggityHank is offline HiggityHank  United States
diyAudio Member
HiggityHank's Avatar
Join Date: Mar 2003
Location: Massachusetts
Send a message via AIM to HiggityHank
as long as the tuning is very close, I believe this to be a question of aestetics. (yeah... I can't spell, sue me ) Maybe the experts out there know of some half-refracted-transposed-orange-2-ports-too-damned-close-resonance.... but in my limited experience, I've never come across it.

Do with my opinion what you will... and take the last part with a grain of salt. But when in doubt, make a spare baffle
  Reply With Quote
Old 14th December 2003, 08:21 PM   #3
sreten is offline sreten  United Kingdom
Join Date: Nov 2003
Location: Brighton UK
it doesn't matter one doodly squat.
very nearly sreten.
  Reply With Quote
Old 14th December 2003, 08:28 PM   #4
Variac is offline Variac  Costa Rica
diyAudio Editor
Variac's Avatar
Join Date: Dec 2001
Location: San Francisco, USA San José, Costa Rica
Should I keep these ports separated?
I realize in your case both ports have to fire out the front, but it recently occured to me that having one fire out the front and one out the rear might help average out some room resonances. I sspect that they might be still too close together to make much difference though, considering the wavelengths involved....
"The geek shall inherit the earth"
2017 Burning Amp is November 12 in S.F. Thread here on diyAudio:
  Reply With Quote
Old 15th December 2003, 02:21 AM   #5
Ap is offline Ap
diyAudio Member
Ap's Avatar
Join Date: May 2002
Location: Sydney, Australia
If this is not an isobarik - then use a single volume, this will help average oyut any driver differences
- as for dual ports I would space them at thirds - ie first one at 1/3 width, second at 2/3rds - uneven spacing can result in one port taking more of the load than the other, resulting in mistuning & compression at higher levels.
  Reply With Quote


Should I keep these ports separated?Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
About INPUT RESISTER separated from ground turnA_zpoint Solid State 8 24th June 2010 02:36 PM
GC hums with separated PS wchick Chip Amps 1 6th May 2007 11:09 AM
Separated or Same Chamber Box? suprastar17 Subwoofers 2 19th April 2005 03:32 PM
re-gluing a separated surround speekergeek Multi-Way 1 29th October 2003 02:21 AM
curved ports vs. multiple ports Craig Multi-Way 1 22nd September 2002 08:30 AM

New To Site? Need Help?

All times are GMT. The time now is 04:02 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio