Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Need some help please
Need some help please
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 31st December 2001, 09:53 PM   #1
Subwoofer is offline Subwoofer
diyAudio Member
 
Join Date: Dec 2001
Default Need some help please

Hi All,

I just found this page and it looks like there are alot of knowledgeable people in here.

I am hoping someone can help me out. I am planning to build a subwoofer for my car with 2 12" woofers that I have. My problem is that I do not know what the T/S parameters are for these speakers.

The are made by Electrovoice and the model number is 12TRX. They are quite old, so they are not on their web site. I tried emailing them (Electrovoice) but got no response back.

Anyone in here ever used this woofer before?

I was planning to use them in a bandpass enclosure, can I use a close enough guide to build the enclosure?

Sorry for all the questions and thanks to anyone that can assist.
  Reply With Quote
Old 31st December 2001, 10:15 PM   #2
Super is offline Super  United States
diyAudio Member
 
Join Date: May 2001
Location: Connecticut
Send a message via AIM to Super
Unless you can measure the parameters of the driver, I would suggest going with a sealed enclosure. This is a broad generalization, but you can yield acceptable results using between a 2 and 3 cubic foot sealed enclosure per driver. The best thing to do would be to build some temp enclosures and experiment.
__________________
Bryan
  Reply With Quote
Old 31st December 2001, 10:32 PM   #3
kelticwizard is offline kelticwizard  United States
Wizard of Kelts
diyAudio Moderator Emeritus
 
Join Date: Sep 2001
Location: Connecticut, The Nutmeg State
Need some help please
Old is right. From what I can see from a search, that model had alnico magnets!

Actually, from what I can gather, alnico has some superior properties to ferrite, not sure why the switchover.

Anyway, here is a message board where some people were talking about using the EV 12 TRX. Check the Email addresses-they might be able to help.

http://www.nmr.mgh.harvard.edu/~rees...les_v02_e.html

I read in one message that the EV 12 TRX was different from the EV 12 TRX-B. Wouldn't know for sure.

There are ways of measuring for speaker parameters for the do-it-yourselfer if it comes to that.

Good Luck!!
  Reply With Quote
Old 5th January 2002, 12:36 AM   #4
Subwoofer is offline Subwoofer
diyAudio Member
 
Join Date: Dec 2001
Thanks for the replies. That was one looonnnggg thread.

Can anyone recommend a software program for enclosure simulating?
  Reply With Quote
Old 5th January 2002, 12:48 AM   #5
ucla88 is offline ucla88  Tahiti
diyAudio Member
 
Join Date: Dec 2001
Location: rocklin, CA
why not alnico? since you ask


cruise down to the bottom of this page for some interesting tidbits on magnet materials.

more LDSG
  Reply With Quote
Old 5th January 2002, 12:54 AM   #6
Subwoofer is offline Subwoofer
diyAudio Member
 
Join Date: Dec 2001
Sorry, should have included this with my second post. Is there a FAQ somewhere on this page that can instruct me on how to measure the T/S parameters? I have never done this before.

Thanks again.
  Reply With Quote
Old 5th January 2002, 03:43 AM   #7
kelticwizard is offline kelticwizard  United States
Wizard of Kelts
diyAudio Moderator Emeritus
 
Join Date: Sep 2001
Location: Connecticut, The Nutmeg State
Need some help please
Here is one link: http://www.epanorama.net/documents/a...arameters.html

This one has a link to a nice spreadsheet to simplify matters: http://www.spiceisle.com/audiodiy/measure.htm

A lot of people recommend this freeware. I can't get the thing to work, but it is recommended by many: http://www.audua.com/

This is an extremely nifty tone generator. I save mine to Program Files, so I can have it any time I want. You can either go up or down in preselected amounts, OR you can highlight the frequency display box and write in any frequency you want. Normally, you want to put it in sine wave mode for testing speakers, of course. You can go from 100 Hz to 99 Hz to 98 Hz, etc., if you want to. Just hook your sound card up to your stereo amp, and you are all set.
http://www.nch.com.au/action/index.html#TONE
  Reply With Quote

Reply


Need some help pleaseHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


New To Site? Need Help?

All times are GMT. The time now is 08:54 AM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio
Wiki