Go Back   Home > Forums > Loudspeakers > Subwoofers

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 11th May 2013, 09:43 AM   #3461
diyAudio Member
 
Join Date: Aug 2011
Thanks for the replies I just get the message:

Can't create output file: C:\Hornresp\hornresp.exe

When I try and unzip the new file-never had the issue before and more than a little of a PC neanderthal! Any suggestions?
  Reply With Quote
Old 11th May 2013, 10:26 AM   #3462
diyAudio Member
 
Join Date: Nov 2006
is hornresp still open?
is the file write-protected?

or:

Try renaming the old hornresp directory, then install it again and if that was successfull, copy the "old" XXXX.dat File into the new directory.
  Reply With Quote
Old 11th May 2013, 12:50 PM   #3463
diyAudio Member
 
Join Date: Aug 2011
Thanks, sorted it. Now, if I could just work out how to use it!
  Reply With Quote
Old 12th May 2013, 07:17 PM   #3464
diyAudio Member
 
Join Date: Sep 2005
Where can I get Hornresp Version 18.00?
  Reply With Quote
Old 13th May 2013, 06:48 AM   #3465
diyAudio Member
 
Join Date: Jun 2007
Quote:
Originally Posted by kerrystansbury View Post
Where can I get Hornresp Version 18.00?
Hi kerrystansbury,

Hornresp Version 18.00 is no longer available. The current release Version 32.20 can be downloaded from the website address shown at the bottom of this post.

Kind regards,

David
__________________
www.hornresp.net
  Reply With Quote
Old 13th May 2013, 04:20 PM   #3466
NEO Dan is offline NEO Dan  United States
diyAudio Member
 
NEO Dan's Avatar
 
Join Date: Jun 2008
Location: N.E. Ohio
Quote:
Originally Posted by kerrystansbury View Post
Where can I get Hornresp Version 18.00?
What was in v18 that you miss?
__________________
Regards,
Dan
  Reply With Quote
Old 13th May 2013, 06:31 PM   #3467
kees52 is offline kees52  Netherlands
diyAudio Member
 
Join Date: May 2009
Location: Sprang-capelle Holland.
I have problems I think with new version. I do see it do not fill in proper width
it need to be 33 : 2 =16.50 but it is 16.49 for S2 but S1 give 0.013485??.

very strange outcomes with horn data,

Length (cm) Area (sq cm) Radius (cm) Angle (deg) Side Len (cm) Height/2 (cm) Top Len (cm) Width/2 (cm) Width Flare

0.000000 135.000000 6.555291 1.738311 0.000000 0.013485 0.000000 2502.803030 Uni
0.500000 135.625000 6.570447 1.734304 0.500090 0.013547 0.500000 2502.793556 Uni
1.000000 136.250000 6.585569 1.730324 1.000180 0.013610 1.000000 2502.784081 Uni
1.500000 136.875000 6.600656 1.726371 1.500269 0.013672 1.500000 2502.774606 Uni
2.000000 137.500000 6.615709 1.722446 2.000359 0.013735 2.000000 2502.765131 Uni
2.500000 138.125000 6.630728 1.718547 2.500449 0.013797 2.500000 2502.755657 Uni
3.000000 138.750000 6.645713 1.714674 3.000539 0.013860 3.000000 2502.746182 Uni
3.500000 139.375000 6.660664 1.710827 3.500628 0.013922 3.500000 2502.736707 Uni
4.000000 140.000000 6.675581 1.707006 4.000718 0.013985 4.000000 2502.727231 Uni
4.500000 140.625000 6.690465 1.703211 4.500808 0.014047 4.500000 2502.717756 Uni
5.000000 141.250000 6.705317 1.699441 5.000898 0.014110 5.000000 2502.708281 Uni
5.500000 141.875000 6.720135 1.695696 5.500987 0.014172 5.500000 2502.698806 Uni
6.000000 142.500000 6.734921 1.691975 6.001077 0.014235 6.000000 2502.689330 Uni
6.500000 143.125000 6.749674 1.688279 6.501167 0.014297 6.500000 2502.679855 Uni
7.000000 143.750000 6.764395 1.684607 7.001257 0.014360 7.000000 2502.670379 Uni
7.500000 144.375000 6.779085 1.680959 7.501347 0.014422 7.500000 2502.660904 Uni
8.000000 145.000000 6.793742 1.677334 8.001436 0.014485 8.000000 2502.651428 Uni
8.500000 145.625000 6.808368 1.673733 8.501526 0.014547 8.500000 2502.641952 Uni
9.000000 146.250000 6.822963 1.670155 9.001616 0.014610 9.000000 2502.632476 Uni
9.500000 146.875000 6.837526 1.666600 9.501706 0.014672 9.500000 2502.623001 Uni
10.000000 147.500000 6.852059 1.663067 10.001795 0.014735 10.000000 2502.613525 Uni

when do with petals it looks better,

Length (cm) Area (sq cm) Radius (cm) Angle (deg) Side Len (cm) Width/2 (cm) Inradius (cm) Petals

0.000000 135.000000 6.555291 1.738311 0.000000 5.809475 5.809475 4
0.500000 135.625000 6.570447 1.734304 0.500180 5.822907 5.822907 4
1.000000 136.250000 6.585569 1.730324 1.000360 5.836309 5.836309 4
1.500000 136.875000 6.600656 1.726371 1.500539 5.849679 5.849679 4
2.000000 137.500000 6.615709 1.722446 2.000717 5.863020 5.863020 4
2.500000 138.125000 6.630728 1.718547 2.500894 5.876330 5.876330 4
3.000000 138.750000 6.645713 1.714674 3.001070 5.889609 5.889609 4
3.500000 139.375000 6.660664 1.710827 3.501246 5.902859 5.902859 4
4.000000 140.000000 6.675581 1.707006 4.001420 5.916080 5.916080 4
4.500000 140.625000 6.690465 1.703211 4.501594 5.929271 5.929271 4
5.000000 141.250000 6.705317 1.699441 5.001768 5.942432 5.942432 4
5.500000 141.875000 6.720135 1.695696 5.501940 5.955565 5.955565 4

when I do make S1 the same as S2 (185 cm2) it is oke again.

Length (cm) Area (sq cm) Radius (cm) Angle (deg) Side Len (cm) Height/2 (cm) Top Len (cm) Width/2 (cm) Width Flare

0.000000 185.000000 7.673808 0.000000 0.000000 16.490000 0.000000 2.804730 Uni
0.500000 185.000000 7.673808 0.000000 0.500000 16.490000 0.500000 2.804730 Uni
1.000000 185.000000 7.673808 0.000000 1.000000 16.490000 1.000000 2.804730 Uni
1.500000 185.000000 7.673808 0.000000 1.500000 16.490000 1.500000 2.804730 Uni
2.000000 185.000000 7.673808 0.000000 2.000000 16.490000 2.000000 2.804730 Uni
2.500000 185.000000 7.673808 0.000000 2.500000 16.490000 2.500000 2.804730 Uni
3.000000 185.000000 7.673808 0.000000 3.000000 16.490000 3.000000 2.804730 Uni
3.500000 185.000000 7.673808 0.000000 3.500000 16.490000 3.500000 2.804730 Uni
4.000000 185.000000 7.673808 0.000000 4.000000 16.490000 4.000000 2.804730 Uni
4.500000 185.000000 7.673808 0.000000 4.500000 16.490000 4.500000 2.804730 Uni
5.000000 185.000000 7.673808 0.000000 5.000000 16.490000 5.000000 2.804730 Uni
5.500000 185.000000 7.673808 0.000000 5.500000 16.490000 5.500000 2.804730 Uni

when I do S1 135 2cm it is a strange outcome, do i miss something or is there a bug, maybe S1 135 2cm is to small, or there is a bug, from S2 it is oke.

Never seen this.

regards

kees
Attached Images
File Type: jpg ScreenHunter_04 May. 13 20.25.jpg (62.9 KB, 87 views)

Last edited by kees52; 13th May 2013 at 06:58 PM.
  Reply With Quote
Old 13th May 2013, 06:50 PM   #3468
kees52 is offline kees52  Netherlands
diyAudio Member
 
Join Date: May 2009
Location: Sprang-capelle Holland.
Oke if I make width 33 cm in stead of height then it is oke I think, I do use uni flare but don,t I need conical for a tapped horn>?

Length (cm) Area (sq cm) Radius (cm) Angle (deg) Side Len (cm) Height/2 (cm) Top Len (cm) Width/2 (cm) Width Flare

0.000000 135.000000 6.555291 1.754989 0.000000 2.045000 0.000000 16.503667 Uni
0.500000 135.631000 6.570593 1.750904 0.500000 2.054561 0.500091 16.503644 Uni
1.000000 136.262000 6.585859 1.746848 1.000000 2.064123 1.000183 16.503620 Uni
1.500000 136.893000 6.601090 1.742820 1.500000 2.073684 1.500274 16.503597 Uni
2.000000 137.524000 6.616287 1.738819 2.000000 2.083246 2.000366 16.503573 Uni
2.500000 138.155000 6.631448 1.734846 2.500000 2.092807 2.500457 16.503549 Uni
3.000000 138.786000 6.646575 1.730900 3.000000 2.102369 3.000548 16.503526 Uni
3.500000 139.417000 6.661667 1.726981 3.500000 2.111931 3.500640 16.503502 Uni

Hmmm I see Hornresp will update but i get a very strange site if I agree with
a update.

Maybe i have a virus, I go do a control of the pc, I have avira.

see here
Attached Images
File Type: jpg ScreenHunter_06 May. 13 20.48.jpg (186.0 KB, 89 views)

Last edited by kees52; 13th May 2013 at 07:04 PM.
  Reply With Quote
Old 13th May 2013, 09:04 PM   #3469
Zero D is offline Zero D  United Kingdom
diyAudio Member
 
Join Date: Aug 2009
[QUOTE]
Quote:
Originally Posted by kees52

I have avira.
Yeah me too Nothing bad happens when i visit -http://www.joynic.com but it's strange how you got there ?

Are you SURE you clicked on Hornresp in David McBean's RECENT posts ?
  Reply With Quote
Old 13th May 2013, 11:48 PM   #3470
NEO Dan is offline NEO Dan  United States
diyAudio Member
 
NEO Dan's Avatar
 
Join Date: Jun 2008
Location: N.E. Ohio
When reporting an issue...
Along with your screen shots and descriptions it would be helpful if you could export the hornresp record and either attach the file or post it to the thread.
Code:
I find the "code" tag # is useful for things like this...
__________________
Regards,
Dan
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Hornresp Class FlipC Subwoofers 8 3rd November 2008 06:23 PM
Some questions about hornresp brsanko Full Range 4 18th October 2008 09:36 PM
Hornresp help / JX150 316a Multi-Way 0 11th February 2004 03:56 PM


New To Site? Need Help?

All times are GMT. The time now is 02:43 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2