Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Solid State Talk all about solid state amplification.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 28th September 2001, 04:35 PM   #1
hugobross is offline hugobross  Europe
diyAudio Member
Join Date: Jun 2001
Location: Flanders, Belgium
Hi, I'm building a 2 x 500W rms amplifier for use on parties etc... This amp excists of 4 mono-amplifiers (bridged to eachother) and a power supply of 2 x 50 V.
Do you know "big" the capacitance must be to play loud and clearly without any distortion?? Right now, I've already 6 capacitors of 37000 µF.

Thanks anyway.

  Reply With Quote
Old 28th September 2001, 04:37 PM   #2
hugobross is offline hugobross  Europe
diyAudio Member
Join Date: Jun 2001
Location: Flanders, Belgium
Exclamation I forgot this

the minimum load of the amp is 8 ohm.

  Reply With Quote
Old 28th September 2001, 05:24 PM   #3
tsz is offline tsz  Sweden
diyAudio Member
Join Date: Aug 2001
Location: Göteborg, Sweden
Send a message via ICQ to tsz
With 3 * 37,000 ( I assume that you meant that there is 6*37,000 per monoblock) per rail and a peak current of about 12 amp (1152 W in 8 ohm) gives a ripple voltage of approximately 0,76V peak to peak, not likely to be audible. But you can't have to much capacitance
ESP has a nice article: http://sound.westhost.com/power-supplies.htm


[Edited by tsz on 09-28-2001 at 11:53 AM]
  Reply With Quote
Old 29th September 2001, 01:39 PM   #4
djk is offline djk
diyAudio Member
djk's Avatar
Join Date: Feb 2001
Location: USA
The Carver M1.5T that I used to own had a single pair of 3,400µF caps to put out 1,200W at 8 ohm in bridge mode."The values for power supply capacitance can be realistically determined by a consideration of the numerical value of W C R where W is the line frequency (377 rad/sec), C is the power supply capacitance, and R is the load resistance.

For this amplifier, the design load is 8 Ohms (although it will easily drive 4 Ohms) at full power. An WCR value of 10 yields about 10 per cent ripple (pk.-pk. ) and a value of 100 has about two percent. Below 10, the power supply will have serious problems and values of about 100 will achieve diminishing performance returns. The minimum value then, for each of the four power supply capacitors should be about 3,000uF and the maximum about 30,00OuF. Capacitances above this value may cause diode bridge failure due to turn-on surges and are not recommended." http://www.passlabs.com/projects/a40_9.htm

  Reply With Quote


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
What would you recommend? bjackson Chip Amps 0 21st November 2005 05:17 PM
what do you recommend pd0019 Multi-Way 0 23rd February 2005 07:40 AM
Recommend a kit for me! Frank Z Tubes / Valves 11 8th October 2003 12:43 AM
Can you recommend me. jleaman Solid State 1 26th February 2003 11:50 PM
What do you recommend for first DIY? Me@Home Multi-Way 10 23rd June 2002 01:04 AM

New To Site? Need Help?

All times are GMT. The time now is 12:17 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio