One more amp - diyAudio
Go Back   Home > Forums > Amplifiers > Solid State

Solid State Talk all about solid state amplification.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 17th November 2002, 03:55 PM   #1
Vivek is offline Vivek  India
diyAudio Member
 
Join Date: Nov 2000
Location: Bangalore, India
Default One more amp

Hi,
Check out http://users.auth.gr/~mixos/projects/nopcb/audio/005/
Any comments would be most welcome.

Cheers,
Vivek
  Reply With Quote
Old 17th November 2002, 10:44 PM   #2
diyAudio Member
 
Join Date: Jul 2001
Location: Orleans, France
Good design, but as usual, missing temperature coefficient correction for the output devices, no resistors in source connexions, no resistors in Q1-Q2 emitters, very common omissions...

Regards, Pierre Lacombe.
  Reply With Quote
Old 17th November 2002, 11:26 PM   #3
lohk is online now lohk  Europe
diyAudio Member
 
lohk's Avatar
 
Join Date: Apr 2001
Location: Northern Noricum, near the Limes
Did you copy it from there ?

http://space.tin.it/scienza/fladelle/

Whose design is it then?

Klaus

ps: just a personal opinion: I will never make any non-class-a amp with mosfets again... this sound always failed to satisfied me
  Reply With Quote
Old 17th November 2002, 11:30 PM   #4
diyAudio Member
 
traderbam's Avatar
 
Join Date: Jan 2002
Location: Earth
Why does the design need emitter resistors for Q1 and Q2 Pierre?

I notice there is no miller cap across Q7 - this is often used to help stability and linearise Q7s Ccb.

This may be the reason why the designer has chosen a high frequency feedback path through R8 and C9 from the gate drive. As a rule I don't like multiple feedback paths, especially from the gate drive because the voltage signal here is highly distorted, especially with FET outputs.

The bias arrangement for the FETs is too crude for a single-ended VAS. The bias voltage will be asymmetrically modulated by the drive current, especially with C10 being a puny 1uF. This should be replaced with a BJT and a 50uF cap in parallel. As Pierre says you might get thermal runaway if the FETs don't have source resistors - depends upon the choice of FETs.

C3 and C5 should be 1000uF or more. The circuit will perform better if the LTP and VAS stages have regulated psus.

Otherwise I like it. It uses competent and independent CCS for both LTP and VAS outputs. It is about as simple as it can be. It uses a VAS output current of >20mA for good gate drive capability.
  Reply With Quote
Old 17th November 2002, 11:37 PM   #5
halojoy is offline halojoy  Sweden
On Hiatus
 
Join Date: Nov 2002
Default 25 watt mosfet amp

I recognize this little amp. One of my absolute favourites!
A very good quality NO NONSENSE design.
25 Watt is also a good choice. The need for more Watts is unusual.
Parts are cheap.
Why not build a biamp, active system
with a multiple number of this amplifier.

As traderbam points out, you can do modifications (mod),
if you like to do that.

The orignal is coming from "RED FREE CIRCUITS DESIGNS"
They have a lot of other useful and sound circuits.
Recommended.

RED FREE CIRCUITS DESIGNS - Audio


Click the image to open in full size.
  Reply With Quote
Old 18th November 2002, 12:31 AM   #6
halojoy is offline halojoy  Sweden
On Hiatus
 
Join Date: Nov 2002
Default technical data - not that bad

Technical data:

Output power: well in excess of 25Watt RMS @ 8 Ohm (1KHz sinewave)

Sensitivity: 200mV input for 25W output

Frequency response: 30Hz to 20KHz -1dB

Total harmonic distortion @ 1KHz: 0.1W 0.014% 1W 0.006% 10W 0.006% 20W 0.007% 25W 0.01%
Total harmonic distortion @10KHz: 0.1W 0.024% 1W 0.016% 10W 0.02% 20W 0.045% 25W 0.07%
Unconditionally stable on capacitive loads

---------------------------------------------------------------------

Here are some other Audio Circuits and Amplifiers
at the homepage Vivek first mentioned in this thread.

Audio Circuits with Amplifiers
  Reply With Quote
Old 24th November 2002, 08:47 AM   #7
2Bak is offline 2Bak  Denmark
diyAudio Member
 
Join Date: Apr 2002
pcb for 25 watt amp

Does anyone have the pcb-layout for the 25 watt amp in question?

I need a three-channel amp running center and rear in a small room.

thanks
/Jan
  Reply With Quote
Old 24th November 2002, 11:56 PM   #8
diyAudio Member
 
Join Date: Jul 2001
Location: Orleans, France
Traderbam,

Resistors in emitters of each transistor in the differential pair are needed to avoid saturation of theese transistors by important transients at the input. This effect has been discovered in 1972 by Pr. Matti Ottala :

For stability, phase compensation is always implemented in this kind of design. Here is C9 and R8. This phase compensation causes a time-lag in signal propagation, and when a transient signal comes at the input, there is a very short time during which the overall feedback is inactive, causing a very inconvenient phenomenon called transient intermodulation distortion.

This phenomenon is totally unnoticeable by conventionnal distortion measurement in continuous sinewave, but addition of some resistors in the emitters of the input pair causes a very audible improvement in sound quality with musics as percussions, hapsichord, etc. (about 68 to 100 ohms).

Furthermore, another problem exist with C7. This electrolytical capacitor works with near zero volt dc across it. Under this conditions, electrolytical capacitors are unable to produce oxygen, wich is needed to maintain the integrity of the aluminium oxyde layer along the time. This causes distortion because of the asymetrical behaviour of the capacitor (which is not apparent when the capacitor is new, and the oxyde layer intact...) To avoid this effect, C7 must be made from 2 series connected capacitors, side reversed, and the common connexion must be biased at 3 to 5 vdc with a large resistor, say 100 kohms. But some distortion can remain at the very low frequencies (quite inaudible). Very high quality capacitors are recommended for C7.


Regards, Pierre Lacombe.
  Reply With Quote
Old 25th November 2002, 04:09 AM   #9
The one and only
 
Nelson Pass's Avatar
 
Join Date: Mar 2001
Default Re: 25 watt mosfet amp

Quote:
Originally posted by halojoy
NO NONSENSE
Almost none. I see 7 parts that you could lose and never
miss.



Make that 8.

Give me a clean supply and I'll make that 12.

  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



New To Site? Need Help?

All times are GMT. The time now is 12:49 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2