help my amp is broked and im sad... - diyAudio
Go Back   Home > Forums > Amplifiers > Solid State

Solid State Talk all about solid state amplification.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 11th May 2005, 05:46 PM   #1
diyAudio Member
 
Join Date: May 2005
Location: London
Send a message via MSN to wowitsjack
Default help my amp is broked and im sad...

hey i was wondering if anyone could help me, i know its a vague problem but basically my amp is only playing through one speaker. i know it isnt the speakers cuz i tried another pair and its still the same, everything seems set up properly too...does anyone know what i should do?
oh yeh its a rotel 'RX-803' if that helps
  Reply With Quote
Old 11th May 2005, 08:00 PM   #2
Netlist is offline Netlist  Belgium
diyAudio Moderator Emeritus
 
Netlist's Avatar
 
Join Date: Jan 2003
Did you party? Look for blown fuses first.
Reverse your inputs, check the input switch (if any, don't know that amp) by toggling it.
If you are somehow familiar with soldering, try checking for bad solder contacts.

/Hugo
  Reply With Quote
Old 11th May 2005, 09:41 PM   #3
diyAudio Member
 
BobEllis's Avatar
 
Join Date: Sep 2003
Location: Upstate NY
does it have a headphone jack? Does that work?

is it one dead channel on all inputs? (tuner, cdp, etc) if not look upstream - cables, source.

do you get an output on both tape outputs if equipped?
  Reply With Quote
Old 12th May 2005, 10:54 AM   #4
diyAudio Member
 
destroyer X's Avatar
 
Join Date: Feb 2004
Location: Recife - Brasil Northeast
Default If have no experience, try to detect the defective channel, use finger-O-meter...

Touch the amplifiers small transistor with your finger...have to discover were are the power amplifiers.... and the input will be small transistors....two of them will be very near one related other...those are the input....touch in many ways there...nothing happened...that side is defective.... ask help to someone to put marks over each transistor that have connections to that burned channel....examine copper traces and watch for interruptions and signal of burns...black smoke or any sign of shorted circuit consequences.

If not fuse.... may be transistors..... the big majority of them are cheap...costing half of nothing!...expensive only output...and not too much .... one or two dollares each one.....so.

Better than search for details.... check only if some sign of fire is founded..... and go scrathing the transistor positions...remove one by one substituting with new units.... do not even check with meters if burned or not!....do not loose time.... substitute them all, one by one.


This is the easiest, and faster method to repair...used in many repair places around the world...they perceived that spend less time doing this way...and parts are not so expensive...time is expensive, patience too , those things are worst.... spend time and good mood!


If experienced you may be laughing..... but you may be wrong, because many times i checked that.... one experienced guys measuring and checking for troubles.... using schematic and all tools, Scopes, meters....and at his side a young teenager starting to make good solders......starting and knowing about half of nothing the one could repair equipment 4 times faster than the experienced one.

And "knowing nothing".... i new professional.... the man that goes replacing....changing parts...the CHANGENEER (Change-Engineer)

OH!..do not laugh to much because of Big fat Charlie here....you may be ashamed if try this "Stone Aged" method.

regards,

Carlos
__________________
These words sounds alike English..but they are not.. these are words without meaning, just sounds made by humans; https://www.youtube.com/watch?v=_X_7iMHugXM
  Reply With Quote
Old 12th May 2005, 10:58 AM   #5
diyAudio Member
 
destroyer X's Avatar
 
Join Date: Feb 2004
Location: Recife - Brasil Northeast
Default Touching transistors with your finger, you will produce loud low frequency sound.

Your home is full of wires...and 60 hertz or 50 hertz mains are travelling and surrounding those wires you have enormous magnetic fields that can be captured by your body....

Human body is full of diluted metals, salt and watter...all them good to conduct energy..... and to capture electro magnetic fields...so, acting as an aerial...an antenna, you will capture those magnetic energy and will transform them in electricity.... touching the transistor input...it will amplify this low frequency that is using your body as an energy condutor (antenna wire)....a loud tone will be heard at speaker in the channel that is working....the other will not produce sound...this one...the silent one...is the one to have things replaced.

regards,

Carlos
__________________
These words sounds alike English..but they are not.. these are words without meaning, just sounds made by humans; https://www.youtube.com/watch?v=_X_7iMHugXM
  Reply With Quote
Old 12th May 2005, 11:01 AM   #6
diyAudio Member
 
Frank Berry's Avatar
 
Join Date: Sep 2003
Location: Midland, Michigan
Carlos is correct.

A good visual inspection will often point you in the right direction.
Look for electrolytic capacitors that have "bulged" on top.
Look for signs of heat.
If you find burned resistors, find out why they failed and repair the cause before you replace the bad resistors.
__________________
Frank
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



New To Site? Need Help?

All times are GMT. The time now is 09:14 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2