question about supply for 9v mixer - diyAudio
Go Back   Home > Forums > Amplifiers > Solid State

Solid State Talk all about solid state amplification.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 29th July 2002, 10:08 AM   #1
diyAudio Member
 
Join Date: May 2001
Location: Denmark
Default question about supply for 9v mixer

Hi I have build this small mixer. http://space.tin.it/scienza/fladelle/Page53.htm
now i have build op only one chanel. And I am wondering if the
supply can be made in a smarter way .
because all these caps and 22k resistors are maybe double work??

What I was thinking is if the circuit can be made with a supply like this
http://sound.westhost.com/project43.htm

So that it still run on one single 9v battery but All the pin 3 at the single op amp are running from Gnd and the dc blocking cap are used it the input circuit and the after the out put op amp.

IS it posible to do like that ? are the 100 k and the 560R still needet?

Im making balanced output, only mono so im feeding the sec output op amp from 1 to 6 with 150 k and also change R 7 and 8 to 150K. because I have cancel the balance control .

It work just find.

I want to intruduce a phase shift sw after the input module,
can i change the op amp to a dual and run it like when i make balanced output ?
Then make a sw between the inverdet ond non inverted output,
im not sure how to do it because it has variable gain (R9 )

Any help is very wellcome jc DK.
  Reply With Quote
Old 29th July 2002, 11:43 AM   #2
vbd is offline vbd
diyAudio Member
 
Join Date: Jan 2002
Location: Grenoble, France
Yes, you can do that ! But you'll still need the polarizing resistor on non-inverting inputs (R3 in the input module) and a few capacitors to your new ground. The 560 ohms resistors in series with the outputs are here to limit output current and set an output impedance and can be reduced, if the op-amps used are short-circuit protected. The 100k at the output provide a discharge path to the output capacitors and should be left if you keep the capacitive coupling.
To create a mid-point, an interesting component is TLE2426 from Texas Instruments, the same function as project43 but in a single TO92 package ...
The phase inversion can be made with an gain of 1 inverting amp following the input op-amp, as you intend, the variable gain being on the first stage only will set gain for both in-phase and antiphase outputs.
__________________
Denis
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
FS:Mixer ext power supply argonrepublic Swap Meet 10 19th October 2012 07:14 AM
Grounding for Mixer and Bipolar Power Supply bbmonster Instruments and Amps 1 20th March 2009 07:59 AM
DIY mic mixer question K Oscar Everything Else 2 31st July 2008 11:27 AM
Power Supply for SPIRIT FOLIO 10.2 mixer TSN Parts 0 20th December 2007 05:10 AM
mixer module power supply query. jeth Parts 5 14th April 2005 04:21 PM


New To Site? Need Help?

All times are GMT. The time now is 04:51 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2