BeoMaster 2400-2 Volume controle - diyAudio
Go Back   Home > Forums > Amplifiers > Solid State
Home Forums Rules Articles diyAudio Store Gallery Wiki Blogs Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Solid State Talk all about solid state amplification.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 8th November 2004, 02:54 PM   #1
Russell is offline Russell  Denmark
diyAudio Member
 
Join Date: Nov 2003
Location: Denmark
Default BeoMaster 2400-2 Volume controle

Hello.

Does anyone have a schematic over a BeoMaster 2400-2 ?
It is the volume control I am interested in.
And if some one could email it to me I would be happy.

It has the problem that when you touch the volume up touch panel, it will go to MAX output.

Thx.

Best regards Thias Russell
  Reply With Quote
Old 8th November 2010, 05:31 AM   #2
diyAudio Member
 
Join Date: Nov 2010
Russell,

I see this is an old post, but I just picked up Beomaster 2400 and am having the same problem with the volume. Did you every figure it out?

Thanks,
Andy
  Reply With Quote
Old 8th November 2010, 08:02 AM   #3
diyAudio Member
 
east electronics's Avatar
 
Join Date: Jan 2006
Location: Athens GREECE
this machines are nightmare to repair ... but any way schematic is avaiolable feel free to email me

regards sakis
__________________
SERVICE ΕΝΙΣΧΥΤΩΝ ΚΑΙ ΙΑΠΩΝΙΚΩΝ ΜΗΧΑΝΗΜΑΤΩΝ ΗΧΟΥ www.eastelectronics.gr
  Reply With Quote
Old 27th November 2010, 07:56 PM   #4
diyAudio Member
 
Join Date: Oct 2006
Default Beomaster 2400 volume

Hey Andy,

I've got the same issue--did you ever figure it out?

Thanks, greg
  Reply With Quote
Old 28th November 2010, 03:04 AM   #5
diyAudio Member
 
Join Date: Mar 2005
Location: Los Angeles, California
2400 is actually an easy repair. Send it to me and I fix it 4 u.

Art
  Reply With Quote
Old 2nd December 2010, 12:45 PM   #6
Boydk is offline Boydk  Denmark
diyAudio Member
 
Join Date: Feb 2010
Location: Aarhus, Denmark
Hi guys, repaired a lot of those some years back in my old job. Sometimes you just need to clean (spray) the carbon tracks of the potentiometer, but increasingly the later years, the potmeters were broke, meaning the connections between the carbon tracks and the solder pins had died. Just an info. Good luck with the repairs :-)
  Reply With Quote
Old 5th December 2010, 11:26 AM   #7
diyAudio Member
 
Join Date: Oct 2006
Default 2400

Is it easy to get to the potentiometer? My experience with this stuff is pretty limited.

Thanks again, gk
  Reply With Quote
Old 19th March 2017, 08:11 AM   #8
diyAudio Member
 
Join Date: Mar 2007
Location: Maribor
I have Beomaster from my friend on my table. I try to repair that amp for a few days.
It was not working ok...bulbs were dead and volume was not responsive and it was just heard distorded sound on phones-speakers.
I changed all capacitors and replaced all bulbs with new one. BUT ...original bulbs are 15V-1W i have used 14V..50mA!!! so i put 220R across each bulb.
After start up all bulbs are ok all is working, but from phones just little little signal ...amp is in MUTE!
volume touch is responding, so goes up and down, but no sound on phones-speakers.
Here are 2 pictures
So problem is with MUTE.... -12V is present all the time instead 0V on mute fets.
ILUFAULT voltage is not right so LDR is not working... LDR is working ok, because when in accidentaly disconnected +15v supply on control board volume bulb glows at full position an touch was not responding but sound was at max position and i almost damaged earphones because of loud signal.
Ldr control is also working ...i measured voltage ..it goes form 6..7V till 12..13V on emitter of TR23 but not on tr24 that drives ldr...because of not right FAULT voltage?
I read that problems can be made because of bulbs...they not have enough current consumption and not give enough voltage drop on resistor 33R. It was true..without resistor i get 0.8V voltage drop ...now with 220R over each bulb it is 2,5V.
Is it too small???...if you check shematics.
because FAULTIL transistor TR6 is not opened and -12v goes on to the Muting transistors trought 1M resistor
I checked with scope ...and audio signal comes till mutting transistors and there shut down.Also checked modulation frequency on control board- level..ok
Thank you for any help.
Attached Images
File Type: jpg Volume 1.jpg (214.5 KB, 29 views)
File Type: jpg volume 2.jpg (297.7 KB, 28 views)
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Beomaster 6000 Service dshambala Parts 5 13th February 2009 11:43 PM
Pre-amp for BeoMaster esims89 Tubes / Valves 4 26th November 2008 12:57 AM
B&O Parts - Beomaster 1900 Terryphillip Solid State 6 17th February 2007 09:35 AM
WTB Beomaster tranie phimor Swap Meet 0 17th February 2006 09:09 AM
Beomaster 1200 schematic JDeV Solid State 1 28th February 2005 05:50 PM


New To Site? Need Help?

All times are GMT. The time now is 01:15 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999-2017 diyAudio

Content Relevant URLs by vBSEO 3.3.2
Wiki