Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Solid State Talk all about solid state amplification.

Check out this page
Check out this page
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 27th May 2001, 05:11 PM   #1
partyjups is offline partyjups
diyAudio Member
Join Date: May 2001
Location: Denmark

Im thinking about buying some PCB from this page
I think they are very low cost.
Can anyone say something about the quality of the circuit on the 400w power amp?
or if some of the other amp's will be better.
im not looking for a highend hifi power amp but a good amp for Pa systems.

I hope somebody will look at it.

jeppe c.
  Reply With Quote
Old 28th May 2001, 01:10 AM   #2
scotthinson is offline scotthinson
diyAudio Member
Join Date: May 2001
Send a message via AIM to scotthinson
Default I don't know if I'd trust it...

Building an amp with that much power output capability can be a challenge. It requires lots of iron, and lots of patience.

There are a couple of circuit comments I'd like to make, there is no protection for the outputstage or the speakers. If you short the output, you'll lose transistors. If the transistors just die, they'll take a speaker with them. Lots of little things look like they've been left out. For instance, there are no clamping diodes to prevent the inductance of a speaker from putting higher than rail voltages on the output.

  Reply With Quote
Old 3rd June 2001, 06:07 PM   #3
Thoth is offline Thoth
diyAudio Member
Join Date: May 2001
I would advise a MOSFET amp for PA use. In general, Mosfets accept more abuse than transistors. Also, they're not subject to thermal runaway. The bad side is that they cost more and put out more noise and heat.

If you can do the PCB yourself, check out the 550WPC (4 ohm) amp in Randy Slone's book.

If you need the PCB, check out 'www.aussieamplifiers.com'. The designs seem a little dated, but the specs look good. I've never heard one, but have seen good things about them.

Good luck.
  Reply With Quote
Old 4th June 2001, 12:47 AM   #4
djk is offline djk
diyAudio Member
djk's Avatar
Join Date: Feb 2001
Location: USA
http://www.passlabs.com/images/projects/a40f6.jpg The circuit board for this amp is the deal of the century. Still available for only $6 from Old Colony! Who cares? It's only 40 watts. Not really. Jumper Q11 and change R9 to 27K 1/2W(Pass suggests this for the A40 if you are having trouble finding the fet, only use 10K for his design) http://www.passlabs.com/projects/a40_subs.htm Change Q1,2,3,6 to the MPS8099 or 2N5551. Change Q4 and Q5 to the 2N3440/2N5416 pair. Use a heatsink on these. Change R10 to 68 ohms. Delete R13 and D3. R11 will be selected for bias. C4 will be for high frequency response. R14,15 will be changed to one 220 ohm per ouput device. The outputs are to be two each BUZ900D/905D http://www.semelab.co.uk/magnatec_mosdata.htm This will give 400 watts RMS with a 53V+53V 800VA transformer and only two pair of outputs! Don't forget to add 10V gate zeners and output flyback diodes.
  Reply With Quote
Old 4th June 2001, 04:48 AM   #5
ding is offline ding
diyAudio Member
Join Date: Apr 2001
Location: Brisbane Australia
Default Protection


I am interested in your comments regarding both amp and speaker protection. Do you know of any sites which give details of how to go about incorporating these features in an amp design. Or do you have the time to go into it in a bit more depth on the forum.


  Reply With Quote
Old 4th June 2001, 12:22 PM   #6
Geoff is offline Geoff  United Kingdom
diyAudio Member
Join Date: Apr 2001
Location: UK

Motorola Application Note AN485, available at the ON-Semi site, gives details and calculations for the provision of short circuit protection in high power audio amplifiers.

  Reply With Quote


Check out this pageHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
page tubelab.com vax9000 Tubelab 1 21st November 2006 04:15 AM
Posts per page.... planet10 Site Announcements 40 10th June 2004 07:23 PM
my new web page Fred Petersen Swap Meet 12 23rd May 2003 05:49 AM
What language is this web page on? stigla Tubes / Valves 8 7th January 2003 11:46 PM

New To Site? Need Help?

All times are GMT. The time now is 10:45 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio