Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Solid State Talk all about solid state amplification.

a MOSFET amp scheme
a MOSFET amp scheme
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 5th January 2004, 05:54 AM   #1
jamesjung21 is offline jamesjung21  New Zealand
diyAudio Member
jamesjung21's Avatar
Join Date: Dec 2003
Location: New Zealand
Question a MOSFET amp scheme

has anyone ever built this amp before?


It supplies a PCB pattern as well.
Nice spec.

Please give me a comment on this amp-->


POWER RATING at 1KHZ with 0.1% THD 63W/ 8ohm, 105W /4ohm
IMD <0.008%
THD at 60W into 8 ohm and 1 KHZ <0.005%
THD at 60W into 8 ohm and 20 HZ....20 KHZ <0.05%
FREQUENCE RESPONSE [at 35W/8ohm, +0...-3dB] 1.5 HZ.....125 KHZ
SLOW RATE with input filter 20V/uS
DAMPING FACTOR at 8ohm [20HZ...20KHZ] >160
  Reply With Quote
Old 5th January 2004, 01:23 PM   #2
djk is offline djk
djk's Avatar
Join Date: Feb 2001
Location: USA
A class B CFP output stage with voltage gain and hexfets, I wonder how it sounds.

I would try it with a NE5532 and just drive the output stage and bias circuit. Drive one end of Q8 and scape everything off to the left of that.
  Reply With Quote
Old 13th January 2004, 01:00 AM   #3
jecanova is offline jecanova  Brazil
diyAudio Member
Join Date: Jan 2004
Location: Sao Paulo
This is the same schematic from Tom Giesbert published in the Elektor magazine. Is a class AB amplifier suited for igbt or mosfet. I┤ve build dozens of this and it has a very good sound and low distortion, but the circuit is very treacky. Look for the articles with the modifications needed for the IGBT.
Use small square red leds and match them with the multimeter. Match all paired transistors. Fix the first timpot in the mid point before install in the circuit. The 2nd trimpot must be set to 1 k before initial setings. Do the initial settings with small power voltage (+-20V or less). The Elektor┤s pcb has a better design and the courrent transistors are joined to the leds. Remember to match resistors also.
Good look
  Reply With Quote


a MOSFET amp schemeHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
RA-971 Scheme raul_77 Solid State 2 4th February 2008 08:14 AM
Hum cancelling scheme? slor Tubes / Valves 15 24th January 2008 12:07 AM
Here is my scheme... StalfoS Chip Amps 2 15th December 2006 09:09 AM
help me on 845 scheme.... blue_angels Tubes / Valves 10 27th October 2004 06:09 AM

New To Site? Need Help?

All times are GMT. The time now is 06:58 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio