Please help me solve my ground loop issues - Pics and layout attached. - diyAudio
Go Back   Home > Forums > Amplifiers > Solid State

Solid State Talk all about solid state amplification.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 23rd April 2013, 05:13 AM   #1
diyAudio Member
 
Join Date: Feb 2012
Default Please help me solve my ground loop issues - Pics and layout attached.

I'm having ground loop issues when connecting my active crossover to my amp. When my amp is hooked up to my speakers without any input (rca's unconnected), the speakers are completely silent. My amp's chassis and power supply ground is connected to earth ground.

However, after connecting my active crossover (pictured) to my amp, I get ground loop hum. If I leave the earth ground unconnected (the green wire in the first pic) the hum is gone. Just to summarize:

Amp (earthed) + Active Crossover (earthed) = hum
Amp (earthed) + Active Crossover (unearthed) = silent.

It doesn't matter which ground I connect the earth ground in my active crossover (power supply ground, speaker ground, etc), the hum happens when its connected.

I've attached pics of my setup and my layout for both the active crossover power supply and the main board. If you'd like anymore pics or tests for me to do let me know.
Attached Images
File Type: jpg SAM_1494.JPG (552.6 KB, 153 views)
File Type: jpg SAM_1495.JPG (543.1 KB, 145 views)
File Type: png layout1.png (53.1 KB, 141 views)
File Type: png layout2.png (36.1 KB, 142 views)
  Reply With Quote
Old 23rd April 2013, 06:31 AM   #2
diyAudio Member
 
Join Date: Apr 2010
Location: Coffs Harbour, on the east coast
You did mean to say that your amplifier's signal ground is connected to chassis (mains protective) ground?
Is the signal ground of your active filter(s) also connected to chassis and protective ground again?
If so, the answer is there - the signal ground of the crossover unit should not be reconnected to protective
ground via another mains loop.

There are safety issues with floating the signal ground above chassis ground but commercial signal processing
devices are typically isolated or otherwise known as "double insulated" which avoids this chain of secondary
grounding problems. For a basic overview -
Earthing (Grounding) Your Hi-Fi - Tricks and Techniques
__________________
regards
  Reply With Quote
Old 23rd April 2013, 06:48 AM   #3
diyAudio Member
 
Join Date: Feb 2012
Quote:
Originally Posted by Ian Finch View Post
You did mean to say that your amplifier's signal ground is connected to chassis (mains protective) ground?
Yes, but not directly. In my amp, the chassis ground is connected to the power supply ground, and the power supply ground is connected to the signal ground (but not at the exact same point).


Quote:
Originally Posted by Ian Finch View Post
Is the signal ground of your active filter(s) also connected to chassis and protective ground again?
If so, the answer is there - the signal ground of the crossover unit should not be reconnected to protective
ground via another mains loop.

There are safety issues with floating the signal ground above chassis ground but commercial signal processing
devices are typically isolated or otherwise known as "double insulated" which avoids this chain of secondary
grounding problems. For a basic overview -
Earthing (Grounding) Your Hi-Fi - Tricks and Techniques
Yes, my active crossover is connected the same way, earth/chassis ground eventually connects to signal ground.

So are you saying is that by design, active filters and processors are *not* suppose to be connected to chassis ground?
  Reply With Quote
Old 23rd April 2013, 07:25 AM   #4
diyAudio Member
 
Join Date: Jan 2012
Hi

could we have an overhead pic of the internals ,im having trouble tracing the wiring.
  Reply With Quote
Old 23rd April 2013, 07:38 AM   #5
sajti is offline sajti  Hungary
diyAudio Member
 
Join Date: Apr 2003
Location: Vác, Hungary
Just connect the signal ground to the chassis using 10ohm resistor, instead of direct connection, in the crossover. This is easy test. If it will be successful, than You can use 10ohm/5W resistor, parallel with 100nF ceramic capacitor.

Sajti
  Reply With Quote
Old 23rd April 2013, 08:50 AM   #6
diyAudio Member
 
Join Date: Apr 2010
Location: Coffs Harbour, on the east coast
The point is not whether they should be grounded but where. If you connect signal ground to loop after loop of chassis/mains leads used throughout your signal chain, you have created a series of ground loops, right? Take a little time reading the linked article and references to see the bigger picture we all have to deal with in getting into building processors, preamps etc. as opposed to amplifiers which we continuously post on this SS amplifier forum and most of us soon get the hang of. In a typical line level device, the chassis and transformer primary are mains connected but the secondary and PSU is isolated from chassis ground so the output and thus the signal circuitry floats. This is not safe by modern standards and requires a safety "ground lift" device to establish a safe potential for exposed connectors.

As an illustration of what's out there, I bought an Ebay preassembled preamp for a client in a hurry and he was extremely happy but when I checked, only a floating power supply and outputs. It will be safe enough upon connection with good cables to an amplifier but on its own...?

Think of a situation where your active filter is powered by an AC wall-wart or an isolated DC bench power supply. No protective ground, no mains issues and plenty big enough to run several filters and more. Would you still have a ground loop? Nope, and it most likely will kill 95% of the hum too. I build basic preamps this way because it is cheap, relatively safe to use and very low noise but others like to do things more traditionally and correctly with self-contained supplies and all the extra features. Fine, but you need to be aware of the grounding issues of doing it that way. In the past, some amps were fitted with a number of line sockets which kept mains ground in series rather than allowing long loops with other mains outlets, for instance. Others with 2 pin US style line sockets were not particularly safe but seldom had hum issues because there was simply no common protective ground to cause problems.

The grounding issue and procedures can be quite different and vary over the period since the US, along with other countries, changed to grounded mains systems but there is plenty of gear still with 2 wire zip cord. In this country at least, DIYs have always been required to fit protective earth to equipment with metal surfaces or connections that can be touched. Not necessarily for the manufacturers though, as they have to conform to insulation test requirements.

I should add that correctly routed protective earthed systems are lower noise than ungrounded ones but, as others say, it's not so straightforward implementing them in all designs. Formal explanations in Douglas Self's, Bob Cordell's or Randy Slone's and others designers' books can be very good references that include these more complex issues.
Check this subject out in the analog line-level forum too.
__________________
regards

Last edited by Ian Finch; 23rd April 2013 at 09:04 AM.
  Reply With Quote
Old 23rd April 2013, 09:21 AM   #7
diyAudio Member
 
Join Date: Feb 2009
Location: UK
From what I read in these forums, this issue is a perennial gotcha which never gets a satisfactory answer. Some people dogmatically stick to the line that all exposed metalwork in a non-commercial device must be connected with a hefty safety ground to earth, but this must always lead to ground loops when connecting an earthed PC, for example, to an amp..?

Some people suggest that leaving the earth off is 'probably' OK, or that you can rely on signal cables for earth continuity. Some people suggest the home made 'earth lift device' e.g. a hefty bridge rectifier with parallel resistor. None of these solutions fills me with confidence.

Could an expert tell us:
(a) Is it possible for a home constructor to build a mains-powered device that doesn't need an earth? Would this require use of an approved transformer (it doesn't guarantee the user knows what he is doing with it), or even a completely encapsulated approved power transformer with fitted mains socket and switch, and AC out? (If these aren't available, they should be.)
(b) Is it possible to buy an approved 'earth lift device'?

Either of these solutions would, presumably, solve the problem at a stroke.
  Reply With Quote
Old 23rd April 2013, 09:31 AM   #8
AndrewT is online now AndrewT  Scotland
diyAudio Member
 
Join Date: Jul 2004
Location: Scottish Borders
The question should be:
Can I be trained to design and build and test and guarantee the ClassII equipment?

Your life and that of any family and/or visitors depends on the quality of that training and testing.
__________________
regards Andrew T.
  Reply With Quote
Old 23rd April 2013, 09:32 AM   #9
AndrewT is online now AndrewT  Scotland
diyAudio Member
 
Join Date: Jul 2004
Location: Scottish Borders
Coppertop,
have you read my report of the test I carried out on the Disconnecting Network?
__________________
regards Andrew T.
  Reply With Quote
Old 23rd April 2013, 11:01 AM   #10
diyAudio Member
 
Join Date: Feb 2009
Location: UK
Quote:
Originally Posted by AndrewT View Post
Coppertop,
have you read my report of the test I carried out on the Disconnecting Network?
Hi Andrew. No I haven't - do you have a link?

Thanks.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Need help with 60hz hum/ground loop. Schematic attached. Fusion916 Solid State 32 11th October 2012 08:25 PM
Methods of Handling Various Devices and Grounding - Ground Loop Issues mattwalston Analog Line Level 7 10th January 2012 11:08 AM
ground loop layout mosfetmaster Solid State 4 7th January 2011 07:11 PM
hum,ground loop,earth loop problem with your answers please frank2395 Pass Labs 2 17th May 2005 06:46 PM
does connecting mains ground with circuit ground create a ground loop? jarthel Everything Else 0 25th June 2003 12:55 PM


New To Site? Need Help?

All times are GMT. The time now is 08:44 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2