what could be the reasons for High freq roll off after 14khz
 User Name Stay logged in? Password
 Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read Search

 Solid State Talk all about solid state amplification.

 Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
 4th February 2013, 02:27 PM #11 rhythmsandy diyAudio Member   Join Date: Aug 2012 but I would like to know what value of the inductance to be there as output zobel as current value is about 1uH with 10ohm 2W resistor and a .1uf with 10ohm resistor in series is shunted at the output. I have a rolloff starting from 14khz what should be the values of the inductor so that the amp will not oscillate at higher frequencies.. or can i just eliminate the zobel as you said 98% of the amps dont have it. what if the output is connected before the inductor? will the amp oscillate as its RLC circuit? Last edited by rhythmsandy; 4th February 2013 at 02:32 PM.
 4th February 2013, 02:36 PM #12 multisync   diyAudio Member   Join Date: Jan 2008 Location: Carp Most amplifiers that use an ouput inductor have a resistor in parallel with the inductor usually 10 ohms if your amplifier is the same the resultant impedance will never be higher than 10 ohms. measure the amplifier frequency response with an 8 ohm resistor load. Is it flat to 20k? Measure your amplifier frequency response with your speakers connected, use a low power level, you don't want to blow your tweeter. Is it flat? measure the voltage at the tweeter terminals? is it rising as the frequency goes from 20-20,000? check your arithmatic XL=2*pi*F*L =6.28 *20,000* .000018 = 2.26 in parallel with a 10 ohm resistor = 1.8 Zohms if you made a measuring mistake with the inductor it would be much less. Last edited by multisync; 4th February 2013 at 02:43 PM.
 4th February 2013, 04:07 PM #13 rhythmsandy diyAudio Member   Join Date: Aug 2012 im measuring the voltage across the output and its giving as 10mv i believe its the DC offset... but no voltage output as you have specified at the output of the speaker connectors...
 4th February 2013, 04:20 PM #14 rhythmsandy diyAudio Member   Join Date: Aug 2012 sure there is a rolloff atleast by listening since its major change so what is the solution now since this amp would be going for high power application in PA
 4th February 2013, 04:21 PM #15 rhythmsandy diyAudio Member   Join Date: Aug 2012 i have connected the speaker cable directly before the inductor it still worked fine without any problems but at moderate levels but no idea how it sounds at higher level but just have a doubt that will that blow off anything? i dont have a cro thats a major problem..
TANDBERGEREN
diyAudio Member

Join Date: Jan 2011
Location: Fosser, Aurskog-Holand, Akershus, Norway.
Quote:
 Originally Posted by ezavalla It is a Zobel network, not a Linkwitz-Riley one

Damned, You are right.

Linkwiz-Riley we use in filters, as in active crossovers, speaker crossovers and like theese.

I am truly embarrased
__________________
Sooner or later you end up with TANDBERG

Last edited by TANDBERGEREN; 4th February 2013 at 04:24 PM.

 4th February 2013, 04:23 PM #17 rhythmsandy diyAudio Member   Join Date: Aug 2012 did anybody faced such prob before? whats the solution now?
 4th February 2013, 04:36 PM #18 TANDBERGEREN   diyAudio Member   Join Date: Jan 2011 Location: Fosser, Aurskog-Holand, Akershus, Norway. Waiting for an answer to what the value of the ZOBEL-networks components were. I can't really understand such rolloff with correct values there. One could also give the output inductor a check. Ah, You have posted that too. .18uH is it measured, or have you just picked one from a supplier? Tried with 3,9Ohm in paralell? Shuld push the roll-off even higher, but 14Khz is extremely low. What kind of feedback is used? __________________ Sooner or later you end up with TANDBERG Last edited by TANDBERGEREN; 4th February 2013 at 04:41 PM.
 4th February 2013, 04:44 PM #19 rhythmsandy diyAudio Member   Join Date: Aug 2012 here is the schematic you can see the output stage.. Imageshack - lme49810.jpg
 4th February 2013, 04:49 PM #20 TANDBERGEREN   diyAudio Member   Join Date: Jan 2011 Location: Fosser, Aurskog-Holand, Akershus, Norway. C12 and C13 is in place, and with the correct values? I am thinking there must be a feedback problem here, or does the R31 get hot as H***? __________________ Sooner or later you end up with TANDBERG

 Posting Rules You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules
 Forum Jump User Control Panel Private Messages Subscriptions Who's Online Search Forums Forums Home Site     Site Announcements     Forum Problems Amplifiers     Solid State     Pass Labs     Tubes / Valves     Chip Amps     Class D     Power Supplies     Headphone Systems Source & Line     Analogue Source     Analog Line Level     Digital Source     Digital Line Level     PC Based Loudspeakers     Multi-Way     Full Range     Subwoofers     Planars & Exotics Live Sound     PA Systems     Instruments and Amps Design & Build     Parts     Equipment & Tools     Construction Tips     Software Tools General Interest     Car Audio     diyAudio.com Articles     Music     Everything Else Member Areas     Introductions     The Lounge     Clubs & Events     In Memoriam The Moving Image Commercial Sector     Swap Meet     Group Buys     The diyAudio Store     Vendor Forums         Vendor's Bazaar         Sonic Craft         Apex Jr         Audio Sector         Acoustic Fun         Chipamp         DIY HiFi Supply         Elekit         Elektor         Mains Cables R Us         Parts Connexion         Planet 10 hifi         Quanghao Audio Design         Siliconray Online Electronics Store         Tubelab     Manufacturers         AKSA         Audio Poutine         Musicaltech         Holton Precision Audio         CSS         Dx Classic Amplifiers         exaDevices         Feastrex         GedLee         Head 'n' HiFi - Walter         Heatsink USA         miniDSP         SITO Audio         Twin Audio         Twisted Pear         Wild Burro Audio

 Similar Threads Thread Thread Starter Forum Replies Last Post Andyroid Tubes / Valves 31 6th January 2013 09:08 PM HP8903B Tubes / Valves 71 30th April 2012 03:53 AM trv Construction Tips 21 22nd May 2010 10:53 AM DrLex Chip Amps 7 8th December 2009 02:37 PM DIY_newbie Multi-Way 7 13th September 2005 04:06 AM

 New To Site? Need Help?

All times are GMT. The time now is 08:40 PM.