CFP output stage adding more output transistors - diyAudio
Go Back   Home > Forums > Amplifiers > Solid State

Solid State Talk all about solid state amplification.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 2nd February 2013, 08:19 AM   #1
diyAudio Member
 
Join Date: Sep 2009
Location: Pretoria
Default CFP output stage adding more output transistors

Hi all. I have recently built a basic amplifier using this topology. P3A amplifier to be exact.
I was wondering, just as a matter of interest, how does one add more output transistors in parallel with the current two- transistor setup in this CFP output stage???
  Reply With Quote
Old 2nd February 2013, 05:55 PM   #2
diyAudio Member
 
Join Date: Apr 2010
Location: Coffs Harbour
I'd post that question on Rod Elliott's forum or at least search threads there on the P3a. It seems just about every DIY around the planet has played with trying to build their own version and the question would have arisen many times. It's likely been discussed here too if you care to search it.

Having said that, if you read real books and came across Douglas Self's "Audio Power Amplifier Design Manual" or "Self on Audio" in the later editions, you'd come across his "Load Invariant" design which is a "blameless" style CFP amp with 2 pairs of MJL3281/1302 driven by MJE340/350. In a nutshell, the output transistors are simply wired in parallel.

'Nothing complicated, bar the heavy emphasis on very good thermal bonding of the bias transistor to the driver transistor(s) - a lot more positively than in the the P3a, anyway. The issues with CFP are poorly understood thermal compensation schemes and stray inductance (long runs and messy routing) in the output stage, so top-notch PCB layout with increasing care as the number of pairs increases and then base stopper resistors, cap. and zobel bypasses may have to go in too.

CFP can be fine but it doesn't handle stray reactances too well. Keep it simple, short and neat and there should be no oscillation problems for only a few pairs.
__________________
regards
  Reply With Quote
Old 2nd February 2013, 06:15 PM   #3
jaycee is offline jaycee  United Kingdom
diyAudio Member
 
Join Date: Apr 2004
Location: Norwich, UK
Elliot shows such a configuration in his P27 guitar amp. small emitter resistors must be used so that the current is evenly shared by the transistors.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Bipolar/MOSFET CFP output stage ashok Solid State 25 28th November 2010 09:31 AM
Adding secondary of output transformer into cathodes of output stage ? Eico ST-70 freddymac406 Tubes / Valves 3 21st April 2007 06:15 PM
Modern transistors for CFP output for preamp grhughes Solid State 22 20th February 2007 06:07 PM
Adding more transistors to output stage? bowdown Solid State 6 19th January 2007 07:15 PM
driver stage for CFP output. RichardJones Solid State 0 21st April 2003 07:46 PM


New To Site? Need Help?

All times are GMT. The time now is 05:11 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2