You're building a high power amp. Don't try to skimp on the cost, build it as the designer intended, unless you want it to blow up in your face.
Look at the difference between the two devices. IRFP240's are capable of 20A and dissipating 150W in their TO-247 casings. The IRF640 does 18A, but it is a TO-220 case that will only dissipate 125W. You will be reducing the dissipation of the amp to the point where it will blow up. If you use more devices, then you are making a harder load to drive, which will result in instability.
Look at the difference between the two devices. IRFP240's are capable of 20A and dissipating 150W in their TO-247 casings. The IRF640 does 18A, but it is a TO-220 case that will only dissipate 125W. You will be reducing the dissipation of the amp to the point where it will blow up. If you use more devices, then you are making a harder load to drive, which will result in instability.
Last edited:
<<unless you want it to blow up in your face.>> u r right jaycee,i think i missed this point ..
Here is someone who DID build it and did not go "BANG" ... http://www.diyaudio.com/forums/solid-state/164531-another-one-build-av800-av1000.html
It depends on the end use and how much money you want to spend. Vertical OPS = GOBS of power (PA use)... lateral OPS= nicer sound , less power - simpler biasing.
OS
hii lee,Hi
You can find IRFP240 and IRFP9240 at DigiKey or Mouser but they are expensive there.
Where are you from?
I could help you out. I bought 100 each for my project and could sell you 2x4 matched devices.
Regards,
Lee
i am from egypt too far from u but any way thnx 4 trying 2 help me.
and what`s the best way to match these mosfets ??
regards,
shady
Hi
You can find IRFP240 and IRFP9240 at DigiKey or Mouser but they are expensive there.
Where are you from?
I could help you out. I bought 100 each for my project and could sell you 2x4 matched devices.
Regards,
Lee
They are around £3 each at Cricklewood electronics.
Cricklewood Electronics CCTV and Electronic Components
hii lee,
i am from egypt too far from u but any way thnx 4 trying 2 help me.
and what`s the best way to match these mosfets ??
regards,
shady
I didn't intend to travel to Egypt to hand them out to you.
(However, I've been there last December...)
I just asked to get an idea where you could source parts from.
For matching the IRFPs I used the way A.H. proposed and it worked well.
Here you find the full documentation of the AV400 including advice how to match the IRFPs:
http://www.diyaudio.com/forums/atta...2-need-scheme-400w-mosfet-amplifier-av400.zip
Note that when buying IRFPs you should take care to get them from the same batch, preferably from the same tube. This makes it more likely to find some matching ones. You need to buy a lot more than you actually need for your amp because they must match close in order to share the load.
That's why I offered you matched ones.
Here you find my experience with matching the IRFPs:
http://www.diyaudio.com/forums/solid-state/164531-another-one-build-av800-av1000-8.html#post2334814
Where do you have the pcb artwork from? Is is from A.H.?
I can't tell you whether it's correct, sorry.
One thing I like to add is that I recommend to buy some IRF610 to replace Q10 if you experience overcompensated bias.
Last edited:
ok thanks so much Mr. LEE and i hope to c u in egypt next time u r thereI didn't intend to travel to Egypt to hand them out to you.
(However, I've been there last December...)
I just asked to get an idea where you could source parts from.
For matching the IRFPs I used the way A.H. proposed and it worked well.
Here you find the full documentation of the AV400 including advice how to match the IRFPs:
http://www.diyaudio.com/forums/atta...2-need-scheme-400w-mosfet-amplifier-av400.zip
Note that when buying IRFPs you should take care to get them from the same batch, preferably from the same tube. This makes it more likely to find some matching ones. You need to buy a lot more than you actually need for your amp because they must match close in order to share the load.
That's why I offered you matched ones.
Here you find my experience with matching the IRFPs:
http://www.diyaudio.com/forums/solid-state/164531-another-one-build-av800-av1000-8.html#post2334814
Where do you have the pcb artwork from? Is is from A.H.?
I can't tell you whether it's correct, sorry.
One thing I like to add is that I recommend to buy some IRF610 to replace Q10 if you experience overcompensated bias.
regards,
SHADY
- Status
- This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button.
- Home
- Amplifiers
- Solid State
- holton AV400 help..??