Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Solid State Talk all about solid state amplification.

carver HR-895 popping/noise on right channel and headphones - plz help
carver HR-895 popping/noise on right channel and headphones - plz help
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 7th August 2010, 04:15 PM   #1
lolek is offline lolek  United States
diyAudio Member
 
lolek's Avatar
 
Join Date: Aug 2010
Question carver HR-895 popping/noise on right channel and headphones - plz help

Hello,

my new HR-895 turns on, everything seems to be functional ( fixed the power supply a few days ago ), but I noticed the right channel is noisy, similar to a dusty vinyl record, with volume turned down, it becomes more frequent, than at one point there is a popping sound, short an loud...

it is only on the right channel on both A and B, and on headphones...

I did look for loose components, bad solder, visually and by tapping the components, applying some force to the board, etc.... cannot find anything... read posts about possible bad resistors, transistors, caps.. but since the noise is also present on the headphones, the failed component is not in the output section of the amp... is this the pre-amp section? - would it be near the component RCA inputs of the receiver - I do not have much experience with audio devices... how would I identify the section responsible for feeding also the headphone output?

Thank you very much,

lolek
  Reply With Quote
Old 20th December 2010, 02:37 PM   #2
powerdoc is offline powerdoc  United States
diyAudio Member
 
Join Date: Aug 2008
I had the same problem; there are a couple of small signal transistors which go bad, IIRC it's on the board on the back right of the unit, facing the unit head on. Keep looking for the exact ones, I found it with Google.
  Reply With Quote
Old 20th December 2010, 02:40 PM   #3
powerdoc is offline powerdoc  United States
diyAudio Member
 
Join Date: Aug 2008
As a matter of fact, follow this thread:

Carver receiver hr-895 one channel noise
  Reply With Quote
Old 11th April 2011, 02:32 PM   #4
leam123 is offline leam123
diyAudio Member
 
Join Date: Aug 2010
Have one on the bench, same prob. Replace Q704 (2SC2705) and Q702 (2SA1145). These Xsistors go out of spec due to over heating. If possible, install heat sinks on these, as well as Q701 & Q703 (left chan). Use care as the pcb pads are VERY thin and easily damaged. Be sure the pads are CLEAN and solder flows evenly. Good luck. Cheers, Al
  Reply With Quote

Reply


carver HR-895 popping/noise on right channel and headphones - plz helpHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
my carver hr-752 adventfan Solid State 13 18th March 2011 06:06 PM
My carver hr-752 problem adventfan Solid State 3 18th March 2011 05:36 PM
Carver M-1.5t loud noise on one channel hybridge Solid State 1 25th March 2010 12:09 AM
Carver HR-752 making a loud buzzing nikkormat42 Solid State 0 12th September 2008 01:54 AM
popping noise through 1 channel on Radford STA15 jives11 Tubes / Valves 5 28th September 2007 07:44 PM


New To Site? Need Help?

All times are GMT. The time now is 07:30 AM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio
Wiki